Yamaha 006IPTO-F0 Manual Do Utilizador
360
Appendix C: MIDI
DM1000 Version 2—Owner’s Manual
MIDI Data Format
1. DATA FORMAT
1.1 CHANNEL MESSAGE
1.2 SYSTEM COMMON MESSAGE
1.3 SYSTEM REALTIME MESSAGE
1.4 EXCLUSIVE MESSAGE
1.4.1 Real Time System Exclusive
1.4.2 System Exclusive Message
1.4.2.1 Bulk Dump
The following data types of bulk dump are used on the DM1000.
1.4.2.2 PARAMTER CHANGE
The following data types of parameter change are used by the DM1000.
* ‘tx’ indicates that the data can be transmitted from the DM1000, and
‘rx’ indicates that the data can be received by the DM1000.
2. Format Details
2.1 NOTE OFF
(8n)
Reception
If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
If [OTHER ECHO] is ON, these message are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
2.2 NOTE ON
(9n)
Reception
If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
If [OTHER ECHO] is ON, these messages are echoed from MIDI OUT.
If the [Rx CH] matches, these messages are received and used to control effects.
2.3 CONTROL CHANGE
(Bn)
Reception
If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.
If [TABLE] is selected, these message are received if [Control Change Rx] is ON,
and will control parameters according to the [Control assign table] settings.
The parameters that can be set are defined in the Control Change Assign Pa-
rameter List.
If [NRPN] is selected, these messages are received if [Control Change Rx] is ON
and the [Rx CH] matches, and will control the parameter that is specified by the
four messages NRPN control number (62h, 63h) and Data Entry control num-
ber (06h, 26h). Parameter settings are defined in the Control Change Assign Pa-
rameter List.
If [Control Change ECHO] is ON, these messages are echoed from MIDI OUT.
If [TABLE] is selected, these message are received if [Control Change Rx] is ON,
and will control parameters according to the [Control assign table] settings.
The parameters that can be set are defined in the Control Change Assign Pa-
rameter List.
If [NRPN] is selected, these messages are received if [Control Change Rx] is ON
and the [Rx CH] matches, and will control the parameter that is specified by the
four messages NRPN control number (62h, 63h) and Data Entry control num-
ber (06h, 26h). Parameter settings are defined in the Control Change Assign Pa-
rameter List.
Command
rx/tx
function
8n NOTE OFF
rx
Control the internal effects
9n NOTE ON
rx
Control the internal effects
Bn CONTROL CHANGE
rx/tx
Control parameters
Cn PROGRAM CHANGE
rx/tx
Switch scene memories
Command
rx/tx
function
F1 MIDI TIME CODE QUARTER
FRAME
FRAME
rx
MTC
F2 SONG POSITION POINTER
rx
Used when TIME REFERENCE is
MIDI CLOCK.
MIDI CLOCK.
Command
rx/tx
function
F8 TIMING CLOCK
rx
MIDI clock
FA START
rx
Start automix (from the beginning)
FB CONTINUE
rx
Start automix (from the middle)
FC STOP
rx
Stop automix
FE ACTIVE SENSING
rx
Check MIDI cable connections
FF RESET
rx
Clear running status
Command
rx/tx
function
F0 7F dd 06 … F7 MMC
COMMAND
COMMAND
tx
MMC command
F0 7F dd 07 … F7 MMC RESPONSE
rx
MMC response
F0 7F dd 01 … F7 MIDI TIME CODE
rx
MTC full message
Command
rx/tx
function
F0 43 0n 7E … F7 BULK DUMP
DATA
DATA
rx/tx
BULK DUMP DATA
F0 43 2n 7E … F7 BULK DUMP
REQUEST
REQUEST
rx/tx
BULK DUMP REQUEST
Data name
tx/rx
function
‘m’
tx/rx
Scene Memory & Request
(compressed data)
(compressed data)
‘S’
tx/rx
Setup Memory & Request
‘L’
tx/rx
User defined MIDI remote &
Request
Request
‘V’
tx/rx
User defined keys & Request
‘U’
tx/rx
User assignable layer & Request
‘C’
tx/rx
Control change table & Request
‘P’
tx/rx
Program change table & Request
‘Q’
tx/rx
Equalizer library & Request
‘Y’
tx/rx
Compressor library & Request
‘G’
tx/rx
Gate library & Request
‘E’
tx/rx
Effect library & Request
‘H’
tx/rx
Channel library & Request
‘R’
tx/rx
Input patch library & Request
‘O’
tx/rx
Output patch library & Request
‘J’
tx/rx
Bus to Stereo library & Request
‘K’
tx/rx
Surround Monitor library & Request
‘a’
tx/rx
Automix data & Request
(compressed data)
(compressed data)
‘N’
tx/rx
Plug-in Effect Card Data & Request
Command
rx/tx
function
F0 43 1n 3E 0C … F7 RARAMETER
CHANGE
CHANGE
rx/tx
DM1000-specific parameter change
F0 43 3n 3E 0C … F7 PARAMETER
REQUEST
REQUEST
rx/tx
DM1000-specific parameter change
F0 43 1n 3E 7F … F7 PARAMETER
CHANGE
CHANGE
rx/tx
General purpose digital mixer
parameter change
parameter change
F0 43 3n 3E 7F … F7 PARAMETER
REQUEST
REQUEST
rx/tx
General purpose digital mixer
parameter request
parameter request
Type (HEX)
tx/rx
function
1 (01)
tx/rx
Edit buffer
2 (02)
tx/rx
Patch data
3 (03)
tx/rx
Setup data
4 (04)
tx/rx
Backup data
16 (10)
tx/rx
Function (recall, store, title, clear)
17 (11)
rx
Function (pair, copy)
18 (12)
rx
Function (effect)
19 (13)
tx/rx
Sort table
20 (14)
tx/rx
Function (attribute, link)
32 (20)
rx
Key remote
33 (21)
tx/rx
Remote meter
34 (22)
tx/rx
Remote time counter
35 (23)
tx/rx
Automix status
STATUS
1000nnnn 8n
Note off message
DATA
0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity(ignored)
STATUS
1001nnnn 9n
Note on message
DATA
0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity(1-127:on, 0:off)