Yamaha DM2000 Manual Do Utilizador
244
Chapter 19—Pro Tools Remote Layer
DM2000 Version 2—Owner’s Manual
3
Use the faders, Encoders, and [ON] buttons to control the currently selected
send.
send.
For stereo aux input channels (i.e., channels with two send panpots), use the ENCODER
MODE [PAN] (PAN) button to toggle between the left and right panpots, and pan with the
Encoder. When the left panpot is active, the ENCODER MODE [PAN] (PAN) button indi-
cator is lit continuously. When the right panpot is active, the ENCODER MODE [PAN]
(PAN) button indicator flashes.
MODE [PAN] (PAN) button to toggle between the left and right panpots, and pan with the
Encoder. When the left panpot is active, the ENCODER MODE [PAN] (PAN) button indi-
cator is lit continuously. When the right panpot is active, the ENCODER MODE [PAN]
(PAN) button indicator flashes.
Assigning Inserts/Plug-ins
Inserts can be assigned to channels as follows. The Pro Tools transport must be stopped in
order to make these assignments.
order to make these assignments.
1
Press the ENCODER MODE [ASSIGN 4] (INSERT) button.
Its indicator lights up and the [SEL] buttons are set to Insert Select mode.
2
Use the [SEL] buttons to select channels for insert assignment.
The name of the selected channel appears in the INSERT/PARAM section of the display.
The border of the corresponding channel name in the Pro Tools Mix window is highlighted
red.
The border of the corresponding channel name in the Pro Tools Mix window is highlighted
red.
3
Press the EFFECTS/PLUG-INS [5] (ASSIGN) button.
Its indicator flashes, as does the ASSIGN indicator on the display.
4
Use Parameter controls 1–4 to select inserts/plug-ins.
The names of the inserts/plug-ins appear on the display in abbreviated form. When you
select an insert/plug-in other than the current, the corresponding SEL button flashes on the
display.
select an insert/plug-in other than the current, the corresponding SEL button flashes on the
display.
5
To confirm your selection, press the relevant Parameter control’s
push-switch.
push-switch.
The SEL button stops flashing.
While the EFFECTS/PLUG-INS [5] (ASSIGN) button indicator is still flashing, you can
assign more inserts/plug-ins to the same channel. To set insert #5, press the Parameter
Down (SCROLL >) button. Press the Parameter Up (< SCROLL) button to view inserts 1–4
again.
assign more inserts/plug-ins to the same channel. To set insert #5, press the Parameter
Down (SCROLL >) button. Press the Parameter Up (< SCROLL) button to view inserts 1–4
again.
To assign inserts/plug-ins to other channels, use the [SEL] buttons to select them. You’ll
need to press the EFFECTS/PLUG-INS [5] (ASSIGN) button each time you select another
channel.
need to press the EFFECTS/PLUG-INS [5] (ASSIGN) button each time you select another
channel.
To assign the same insert/plug-in to all channels, while holding down the USER DEFINED
KEYS [5] (OPTION/ALL) button, press the Parameter control push-switch. (The number
of assignments possible depends on the available CPU power.)
KEYS [5] (OPTION/ALL) button, press the Parameter control push-switch. (The number
of assignments possible depends on the available CPU power.)
To assign the same insert/plug-in to a selection of channels, press the ENCODER MODE
[ASSIGN 4] (INSERT) button (indicator off) so that the [SEL] buttons can be used to select
channels. Select the channels as explained on page 239, then press the EFFECTS/PLUG-INS
[5] (ASSIGN) button. While its indicator is flashing, use Parameter controls 1–4 to select an
insert/plug-in, and while holding down the USER DEFINED KEYS [5] (OPTION/ALL)
button and USER DEFINED KEYS [4] (SHIFT/ADD) button, press the Parameter control’s
push-switch. (The number of assignments possible depends on the available CPU power.)
[ASSIGN 4] (INSERT) button (indicator off) so that the [SEL] buttons can be used to select
channels. Select the channels as explained on page 239, then press the EFFECTS/PLUG-INS
[5] (ASSIGN) button. While its indicator is flashing, use Parameter controls 1–4 to select an
insert/plug-in, and while holding down the USER DEFINED KEYS [5] (OPTION/ALL)
button and USER DEFINED KEYS [4] (SHIFT/ADD) button, press the Parameter control’s
push-switch. (The number of assignments possible depends on the available CPU power.)
You can cancel this function by pressing the [–/DEC] (ESC) button.