Yamaha HTR-5790 Manual Do Utilizador
21
CONNECTIONS
PRE
P
ARA
T
ION
Both AM and FM indoor antennas are included with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
■
Connecting the AM loop antenna
1
Set up the AM loop antenna, then connect it
to the terminals on this unit.
to the terminals on this unit.
2
Press and hold the tab to insert the AM loop
antenna lead wires into the AM ANT and GND
terminals.
antenna lead wires into the AM ANT and GND
terminals.
3
Orient the AM loop antenna for the best
reception.
reception.
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
• A property installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality, an
outdoor antenna may improve the quality. Consult the nearest
authorized YAMAHA dealer or service center about outdoor
antennas.
outdoor antenna may improve the quality. Consult the nearest
authorized YAMAHA dealer or service center about outdoor
antennas.
■
75-ohm/300-ohm antenna adapter
(U.K. model only)
(U.K. model only)
1
Open the cover of the
included 75-ohm/300-ohm
antenna adapter.
included 75-ohm/300-ohm
antenna adapter.
2
Cut the external sleeve
of the 75-ohm coaxial
cable and prepare it for
connection.
of the 75-ohm coaxial
cable and prepare it for
connection.
3
Cut the lead wire and
remove it.
remove it.
4
Insert the cable
wire into the slot,
and clamp it with
pliers.
wire into the slot,
and clamp it with
pliers.
5
Snap the cover
into place.
into place.
■
FREQUENCY STEP switch
(Asia and General models only)
(Asia and General models only)
Because the interstation frequency
spacing differs in different areas, set
the FREQUENCY STEP switch
(locating on the rear panel) according
to the frequency spacing in your area.
• North, Central and South America: 100 kHz/10 kHz
• Other areas: 50 kHz/9 kHz
Before setting this switch, disconnect this unit’s AC
power cord from the wall outlet.
spacing differs in different areas, set
the FREQUENCY STEP switch
(locating on the rear panel) according
to the frequency spacing in your area.
• North, Central and South America: 100 kHz/10 kHz
• Other areas: 50 kHz/9 kHz
Before setting this switch, disconnect this unit’s AC
power cord from the wall outlet.
Connecting the antennas
MAIN
SURRO
SUB
WOOFE
TUNER
AM
ANT
GND
FM ANT
75
Ω
UNBAL.
COMPONENT VIDEO
P
P
R
VD
ONITOR OUT
TV
P
B
Y
AM loop antenna
(included)
Ground (GND terminal)
For maximum safety and minimum interference,
connect the antenna
connect the antenna
GND
terminal to a good earth
ground. A good earth ground is a metal stake driven
into moist earth.
into moist earth.
Indoor FM antenna
(included)
(included)
Notes
11 (7/16)
8 (5/16)
6 (1/14)
8 (5/16)
6 (1/14)
Unit:
mm (inch)
mm (inch)
Lead wire
Clamp
Clamp
Insert the wire
into slot.
into slot.
100kHz/10kHz
FREQUENCY
STEP
50kHz/9kHz
FM
AM
00_HTR-5790U_EN.book Page 21 Tuesday, December 9, 2003 9:16 AM