Texas Instruments TMS320DM355 Manual Do Utilizador
www.ti.com
PRODUCT PREVIEW
2.5 Pin List
TMS320DM355
Digital Media System-on-Chip (DMSoC)
Digital Media System-on-Chip (DMSoC)
SPRS463A – SEPTEMBER 2007 – REVISED SEPTEMBER 2007
provides a complete pin description list in pin number order.
Table 2-23. DM355 Pin Descriptions
Name
BGA
Type Group
Power
PU
Reset
Description
(4)
Mux Control
ID
(1)
Supply
(2)
PD
(3)
State
CIN7 / GIO101 /
N3
I/O
CCDC
V
DD_VIN
PD
in
Standard CCD Analog Front End (AFE):
PINMUX0[1:0].CIN_
SPI2_SCLK
/ GIO /
NOT USED
7
SPI2
YCC 16-bit: time multiplexed between
chroma: CB/CR[07]
chroma: CB/CR[07]
YCC 08-bit (which allows for 2 simultaneous
decoder inputs), it is time multiplexed
between
decoder inputs), it is time multiplexed
between
luma and chroma of the upper channel.
Y/CB/CR[07]
Y/CB/CR[07]
SPI: SPI2 Clock
GIO: GIO[101]
CIN6 / GIO100 /
K5
I/O
CCDC
V
DD_VIN
PD
in
Standard CCD Analog Front End (AFE):
PINMUX0[3:2].CIN_
SPI2_SDO
/ GIO /
NOT USED
6
SPI2
YCC 16-bit: time multiplexed between
chroma: CB/CR[06]
chroma: CB/CR[06]
YCC 08-bit (which allows for 2 simultaneous
decoder inputs), it is time multiplexed
between luma and chroma of the upper
channel. Y/CB/CR[06]
decoder inputs), it is time multiplexed
between luma and chroma of the upper
channel. Y/CB/CR[06]
SPI: SPI2 Data Out
GIO: GIO[100]
CIN5 / GIO099 /
M3
I/O
CCDC
V
DD_VIN
PD
in
Standard CCD Analog Front End (AFE):
PINMUX0[5:4].CIN_
SPI2_SDENA[0]
/ GIO /
raw[13]
5
SPI2
YCC 16-bit: time multiplexed between
chroma: CB/CR[05]
chroma: CB/CR[05]
YCC 08-bit (which allows for 2 simultaneous
decoder inputs), it is time multiplexed
between luma and chroma of the upper
channel. Y/CB/CR[05]
decoder inputs), it is time multiplexed
between luma and chroma of the upper
channel. Y/CB/CR[05]
SPI: SPI2 Chip Select
GIO: GIO[99]
CIN4 / GIO098 /
L4
I/O
CCDC
V
DD_VIN
PD
in
Standard CCD Analog Front End (AFE):
PINMUX0[7:6].CIN_
SPI2_SDI /
/ GIO /
raw[12]
4
SPI2_SDENA[1]
SPI2 /
SPI2
SPI2
YCC 16-bit: time multiplexed between
chroma: CB/CR[04]
chroma: CB/CR[04]
YCC 08-bit (which allows for 2 simultaneous
decoder inputs), it is time multiplexed
between luma and chroma of the upper
channel. Y/CB/CR[04]
decoder inputs), it is time multiplexed
between luma and chroma of the upper
channel. Y/CB/CR[04]
SPI: SPI2 Data In
GIO: GIO[098]
(1)
I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal.
(2)
Specifies the operating I/O supply voltage for each signal. See
, Power Supplies for more detail.
(3)
PD = pull-down, PU = pull-up. (To pull up a signal to the opposite supply rail, a 1 k
Ω
resistor should be used.)
(4)
To reduce EMI and reflections, depending on the trace length, approximately 22
Ω
to 50
Ω
damping resistors are recommend on the
following outputs placed near the DM355: YOUT(0-7),COUT(0-7), HSYNC,VSYNC,LCD_OE,FIELD,EXTCLK,VCLK. The trace lengths
should be minimized.
should be minimized.
Device Overview
36