GE Monogram ZISW360DM Manual Do Utilizador
Monogram.
™
For answers to your Monogram,
®
GE Profile
™
or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
Underwriters
Laboratories
Specification Revised 2/02
3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be installed on
trimmed models. The overlay panel must be secured to a 1/4" thick
backer panel which slides into the trim. A spacer panel 0.10" thick
must be placed between the overlay and backer panel.
trimmed models. The overlay panel must be secured to a 1/4" thick
backer panel which slides into the trim. A spacer panel 0.10" thick
must be placed between the overlay and backer panel.
Assemble the panels with glue and screws.
• Center the spacer panel on the backer panel, left to right and top to
bottom. Secure the panels with glue.
bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlay panel and
secure with glue and screws. Screws must be countersunk into the
backer panel.
secure with glue and screws. Screws must be countersunk into the
backer panel.
3/4"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
ZISW360DM - GE Monogram 36" Built-In Refrigerator with Dispenser and
Water Filter
Spacer Panel
Overlay Panel
Backer Panel
.250" + .10" + .750" = 1.100" Total Panel Thickness
NOTE: Left-to-right
offset is not always
equal to top-to-bottom
offset.
offset is not always
equal to top-to-bottom
offset.
IMPORTANT NOTE – Dispenser Models
The refrigerator is supplied with two dispenser trims, one for
framed panels and one for overlay panels. The overlay dispenser
trim is designed to fit a total panel thickness of 1.100".
• If the panel is less than 1.100" a noticeable gap may be created
around the dispenser trim.
• If the panel is more than 1.100" the dispenser trim cannot be
secured to the door.
The refrigerator is supplied with two dispenser trims, one for
framed panels and one for overlay panels. The overlay dispenser
trim is designed to fit a total panel thickness of 1.100".
• If the panel is less than 1.100" a noticeable gap may be created
around the dispenser trim.
• If the panel is more than 1.100" the dispenser trim cannot be
secured to the door.
• The overlay panel must be constructed according to the
specifications shown to achieve the correct total thickness.
• Alternative panel construction methods such as securing a 3/4"
panel to a 1/4" backer panel cannot be used. Another method,
routing a 3/4" thick panel on all sides cannot be used. These
methods will not result in the required 1.100" panel thickness.
specifications shown to achieve the correct total thickness.
• Alternative panel construction methods such as securing a 3/4"
panel to a 1/4" backer panel cannot be used. Another method,
routing a 3/4" thick panel on all sides cannot be used. These
methods will not result in the required 1.100" panel thickness.
Fresh Food
Panel
Freezer
Panel
E
D
F
G
A
B
Grille Panel
C
Dispenser
Cutout
9-5/8"
Dispenser Cutout
15-3/8"
A
B
C
D
E
F
G
1/4” Backer Panel
33-7/8
9
68-3/8
14-9/16
18-9/16
.10” Spacer Panel
33
8-3/8
67
13-1/4
17-1/4
3/4" Overlay Panel
34-1/8
9-1/4
68-5/8
14-13/16
18-13/16
17-15/16
3-1/4
*Dispenser
Cutout Position
*Cut the dispenser opening after the backer, spacer and overlay panels
have been assembled.
have been assembled.
IMPORTANT NOTE: Maximum
total weight for assembled fresh
food panel is 50 pounds and 30
pounds for freezer panel.
total weight for assembled fresh
food panel is 50 pounds and 30
pounds for freezer panel.
As an ENERGY STAR
®
Partner,
GE has determined that this product
meets the ENERGY STAR
®
guidelines for energy efficiency.