Southbend X560AA Manual Do Utilizador
500
S
ERIES
R
ESTAURANT
R
ANGES
I
NSTALLATION
O
WNER
’
S
M
ANUAL
1188716
(02/07) P
AGE
15
OF
44
S
TEP
2
B
:
A
TTACH
C
ASTERS AND
R
ESTRAINT
NOTICE
For an appliance equipped with casters, (1) the installation shall be made with a connector that complies with
the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas
Appliances, CAN/CGA-6.16, and a quick-disconnect device that complies with the Standard for Quick-
Disconnect Devices for Use With Gas Fuel, ANSI Z21.41, or Quick Disconnect Devices for Use with Gas Fuel,
CAN1-6.9, (2) adequate means must be provided to limit the movement of the appliance without depending on
the connector and the quick-disconnect device or its associated piping to limit the appliance movement, and (3)
the restraining means should be attached to a frame member on the back of the unit.
the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas
Appliances, CAN/CGA-6.16, and a quick-disconnect device that complies with the Standard for Quick-
Disconnect Devices for Use With Gas Fuel, ANSI Z21.41, or Quick Disconnect Devices for Use with Gas Fuel,
CAN1-6.9, (2) adequate means must be provided to limit the movement of the appliance without depending on
the connector and the quick-disconnect device or its associated piping to limit the appliance movement, and (3)
the restraining means should be attached to a frame member on the back of the unit.
A set of four casters is packed with ranges ordered with casters (instead of legs).
A threaded leg pad is fastened to the base frame at each corner. Each caster has a corresponding mating thread. The
casters can be adjusted to overcome a slightly uneven floor. Casters are provided with a Zerk fitting for proper
lubrication when required.
casters can be adjusted to overcome a slightly uneven floor. Casters are provided with a Zerk fitting for proper
lubrication when required.
1. Raise range sufficiently to allow leg pads and casters to be attached. For safety, “shore up” and support the
range with an adequate blocking arrangement strong enough to support the load.
2. Attach the four leg pads to the bottom of the range using the lock washers and machine screws. The
mounting holes are pre-drilled and threaded.
3. Screw the casters into the holes in the centers of the leg pads. Install the casters that have a locking brake
under the front of the range.
4. Lower range gently onto a level surface. Never drop or allow the range to fall.
5. Use a level to make sure that the range surface is level. The casters can be screwed in or out to lower or raise
each corner of the range. After the range has been leveled, tighten the lock nuts.
Figure 5
Installation of Casters
6. Secure the restraining-device bracket (item “B” in the following illustration) to a wall stud located as close as
possible to the appliance connector inlet and outlet connections. Use four #12 screws (items “C”) and plastic
anchors (items “A”) if necessary.
anchors (items “A”) if necessary.
7. Install eye-bolt (item “F”) to a frame member on the rear of the equipment. After checking carefully behind the
frame member for adequate clearance, drill a 7 mm hole through the frame member.
8. Thread hex nut (item “G”) and slide the washer (item “H”) onto the eye-bolt. Insert the eye-bolt through the 7
mm drilled hole and secure with a washer (item “H”) and nylon lock nut (item “I”).
9. Using the spring-loaded snap hooks, attach the restraining device to the bracket and the eye-bolt.