Vertex Standard FT-2000 Manual Do Utilizador
Page 118
FT-2000 O
PERATING
M
ANUAL
061 A1A FRQDISP
Function: Selects the frequency Display Format for the
CW mode.
Available Values: dir/OFSt
Default Setting: OFSt
CW mode.
Available Values: dir/OFSt
Default Setting: OFSt
dir (Direct Frequency): Displays the receiver carrier
frequency, without any offset
a d d e d . W h e n c h a n g i n g
modes between SSB and CW,
the frequency display re-
mains constant.
a d d e d . W h e n c h a n g i n g
modes between SSB and CW,
the frequency display re-
mains constant.
OFSt (Pitch Offset):
This frequency display re-
flects the added BFO offset.
flects the added BFO offset.
062 A1A PC KYNG
Function: Enables/disables CW keying from the “DATA
IN” terminal on the rear panel’s PACKET jack while op-
erating on the CW mode.
Available Values: EnA (Enable)/diS (Disable)
Default Setting: diS (Disable)
IN” terminal on the rear panel’s PACKET jack while op-
erating on the CW mode.
Available Values: EnA (Enable)/diS (Disable)
Default Setting: diS (Disable)
063 A1A QSKTIME
Function: Selects the time delay between when the PTT
is keyed and the carrier is transmitted during QSK opera-
tion when using the internal keyer.
Available Values: 15/20/25/30 msec
Default Setting: 15 msec
is keyed and the carrier is transmitted during QSK opera-
tion when using the internal keyer.
Available Values: 15/20/25/30 msec
Default Setting: 15 msec
MODE-DAT G
ROUP
064 dAtA DATA IN
Function: Selects the data input path to be used on the
PKT mode.
Available Values: dAtA/PC
Default Setting: dAtA
PKT mode.
Available Values: dAtA/PC
Default Setting: dAtA
dAtA:Uses the data input line connected to pin 1 of
the PACKET jack while using the PKT mode.
PC:
This parameter is for future expansion of this
transceiver’s capabilities, but at this time is not
supported.
transceiver’s capabilities, but at this time is not
supported.
065 dAtA DT GAIN
Function: Sets the data input level from the TNC to the
AFSK modulator.
Available Values: 0 ~ 100
Default Setting: 50
AFSK modulator.
Available Values: 0 ~ 100
Default Setting: 50
066 dAtA DT OUT
Function: Selects the receiver to be connected to the data
output port (pin 4) of the PACKET jack.
Available Values: nAin (Main)/Sub (Sub)
Default Setting: nAin (Main)
output port (pin 4) of the PACKET jack.
Available Values: nAin (Main)/Sub (Sub)
Default Setting: nAin (Main)
067 dAtA OUT LVL
Function: Sets the AFSK data output level at the output
port (pin 4) of the PACKET jack.
Available Values: 0 ~ 100
Default Setting: 50
port (pin 4) of the PACKET jack.
Available Values: 0 ~ 100
Default Setting: 50
068 dAtA VOX DLY
Function: Adjusts the “VOX” delay (receiver recovery)
time on the PKT mode.
Available Values: 30 ~ 3000 msec
Default Setting: 300 msec
time on the PKT mode.
Available Values: 30 ~ 3000 msec
Default Setting: 300 msec
069 dAtA V GAIN
Function: Adjusts the “VOX” gain on the PKT mode.
Available Values: 0 ~ 100
Default Setting: 50
Available Values: 0 ~ 100
Default Setting: 50
070 dAtA PKTDISP
Function: Sets the packet frequency display offset.
Available: –3000 ~ +3000 Hz (10 Hz/step)
Default: 0 Hz
Available: –3000 ~ +3000 Hz (10 Hz/step)
Default: 0 Hz
071 dAtA PKT SFT
Function: Sets the carrier point during the SSB packet
operation.
Available: –3000 ~ +3000 Hz (10 Hz/step)
Default: 1000 Hz (typical center frequency for PSK31,
etc.)
operation.
Available: –3000 ~ +3000 Hz (10 Hz/step)
Default: 1000 Hz (typical center frequency for PSK31,
etc.)
MODE-CW G
ROUP
M
ENU
M
ODE