Melissa 640-073 Manual Do Utilizador
ASSEMBLING THE VACUUM
CLEANER:
CLEANER:
Fitting the tube:
-
-
Press the buttons on the end of the tube and
insert the tube into the air-intake.
insert the tube into the air-intake.
Removing the hose:
-
-
To release the hose, press the buttons on the
end of the hose and pull the hose firmly from
the air intake duct.
end of the hose and pull the hose firmly from
the air intake duct.
OPERATION
-
Do not remove the plug from the socket by
pulling the cable or the appliance itself.
pulling the cable or the appliance itself.
-
Do not run the appliance over the power
cable.
cable.
-
Do not use the appliance to vacuum up lit
matches, cigarette ends or hot ashes.
matches, cigarette ends or hot ashes.
-
Do not use the appliance on wet surfaces.
-
Do not obstruct the air intake or the air outlet
vents.
vents.
-
Do not use the appliance to vacuum up
needles, drawing pins or string.
needles, drawing pins or string.
INSTRUCTIONS FOR USE
-
Before using the appliance, unwind a
sufficient length of cable and insert the plug
into the power socket. A yellow mark on the
power cable shows the ideal cable length.
Do not extend the cable beyond the red
mark.
To rewind the power cable, press the rewind
button with one hand, and guide the cable
with the other hand to ensure that it does
not whip causing damage.
sufficient length of cable and insert the plug
into the power socket. A yellow mark on the
power cable shows the ideal cable length.
Do not extend the cable beyond the red
mark.
To rewind the power cable, press the rewind
button with one hand, and guide the cable
with the other hand to ensure that it does
not whip causing damage.
-
Press the ON/OFF button to switch the
appliance on.
appliance on.
-
The vacuum cleaner’s three special nozzles
can be stored in the storage compartment
(14). Remove the floor nozzle and fit the
special nozzle required to the end of the
telescopic tube. Note: The brush nozzle (18)
must be placed over the joint nozzle (17).
Close the cover again before turning the
vacuum cleaner on (the buttons (15) must be
clicked in place).
can be stored in the storage compartment
(14). Remove the floor nozzle and fit the
special nozzle required to the end of the
telescopic tube. Note: The brush nozzle (18)
must be placed over the joint nozzle (17).
Close the cover again before turning the
vacuum cleaner on (the buttons (15) must be
clicked in place).
-
While in use, the suction force can be
regulated by opening and closing the air
valve on the handle or adjusted electronically
using the suction force regulation slider (13).
regulated by opening and closing the air
valve on the handle or adjusted electronically
using the suction force regulation slider (13).
The nozzles are to be used as follows:
Floor nozzle (11):
Floors, carpets and rugs
Extra nozzle for hard floors (19):
Hard floors
Furniture nozzle (16):
Furniture, curtains, drapes, etc.
Joint nozzle (17):
Radiators, corners, skirtings, etc.
Brush nozzle (18):
Shelves, books, lampshades, etc.
REPLACING THE DUST BAG:
After removing the hose, open the front cover by
pressing the lock lever and pulling upwards.
Remove the dustbag-holder.
Remove the dustbag from the holder.
Replace the dustbag by inserting the carton of
the dustbag into the grooves of the dustbag-
holder.
REPLACING THE MOTORFILTER
The motor-filter is the filter placed behind the
dustbag:
Open the front cover, and gently pull out the filter
free of the holder.
Insert a new motor-filter.
REPLACING THE HEPA FILTER
Open the cover (2) by lifting the buttons (15). Lift
the old HEPA filter out and replace with the new
HEPA filter. Close the cover again before
turning
the vacuum cleaner on (the buttons (15)
must be clicked in place).
must be clicked in place).
DO NOT USE THE VACUUM CLEANER
WITHOUT BOTH FILTERS IN PLACE!
12
640073_IM 19/05/06 14:21 Side 12