Haier HSU-12HEK03/R2(DB) Manual Do Utilizador

Parts and Functions

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Remove the battery cover;

Load the batteries as illustrated. 

2 R-03 batteries, resetting key 

(cylinder);

Be sure that the loading

is in line with th

Load the battery,then put on the cover again.

 The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change- over

wireless telephone is installed in the 

ver is apt to be disturbed in receiving the signals,

so the distance to the indoor unit should be shorter.

type fluorescent lamp or
room, the recei

Note:

Full display or unclear display during operation indicates the 

ries have been used up. Please change batteries.

If the remote controller can't run normally during operation, please 

reload several minutes later.

batte

remove the batteries and

Please be subject to the actual produce purchased the 
above picture is just from your reference

4

Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.

Please be subject to the actual produce purchased the 
above picture is just from your reference

1. Mode display

2. Signal sending display

4. FAN SPEED display

5. LOCK display
6. TIMER OFF display

TIMER ON display

LO

MED

HI

7.TEMP display

16. LOCK button

Used to lock buttons and LCD display.

25. RESET button

When the remote controller 
appears abnormal, use a sharp 
pointed article to press this button 
to reset the remote

22. HOUR button

Operation mode

AUTO

FAN

COOL

DRY

Remote controller

HEAT

1

2

3

4

5

9

10

11

12

13

14

15

16

17

22

23

24

25

19

20

21

8

18

7

6

Control the lightening and extinguishing 
of the indoor LED display board.

3. SWING  display

8.

9. QUIET button
10. HEAT button
11. COOL button
12. AUTO button
13. FAN SPEED button
14. TIMER button
15. HEALTH button

17. LIGHT button

18. POWER ON/OFF button
19. DRY button
20. TEMP button
21. SWING button

23. EXTRA FUNCTION button

24.CANCEL/CONFIRM button

AUTO

Function: Setting and cancel to the 
timer and other additional functions.

Display 
circulated

Operation mode

Remote controller

QUITE

POWER

SLEEP

Supplemented 
    electrical 
     heating

HEALTH

Additional functions display

Healthy function is not available for some units.

Function: Air sending--- Healthy 
airflow position1--- Healthy airflow
position 2 --- Restore the original
flap position --- Right & left air airflow
--- A-B yard---10 and heating symbol
displayed simultaneously--- Sleeping
--- Electrical heating--- Refresh air
(

reserved function)  

---    Power   --- 

Fahrenheit/Celsius mode conversion

Air Purifying Filter

(inside)

Inlet

1

Inlet grille

2

Outlet

4

(adjust left and right air flow) 

Vertical blade

6

 Display board

Horizontal flap

(adjust up and down air flow.

  Don't adjust it manually)

Emergency  Switch

7

8

3

5

1

2

4

6

5

7

3

1

EK3

8

1

2

3

4

5

8

6

7

EK1 display board

EK3 display board

Display board

When receiving the remote control 
signal,display the set temperature 
and in the rest time the room 
temperature is displayed and this 
room temperature is only for reference.

Signal receiver hole
ON/OFF display
Ambient temp.display

TIMER ON/OFF display
TIMER ON-OFF display
SLEEP display

Note to the power failure resume:

Press the sleep button ten times in five seconds and enter function 
after hearing four sounds.And press the sleep button ten times 
within five seconds and leave this function after hearing two sounds.

EK1

COOL\HEAT\DRY\AUTO display

4

5

4

5
6

RUNNING display

2

4

6