Mission mv-2 Guia Do Utilizador

Troubleshooting

Television picture colour is distorted

Subwoofer too close to TV. (Switch off system and TV. Move units away. Leave 15 mins. Switch on.

Excessive bass distortion at low volumes Subwoofer level set too high; LFE level set too high; Subwoofer incorrectly wired

Excessive or distorted bass at high levels

System level set too high; Bass control set too high; Speakers too close to room corners

Popping or thumping from the subwoofer

System level set high; Subwoofer level set too high; LFE level set too high

Indistinct sound; Poor localisation of
effects. Poor localisation of dialogue

One or more loudspeakers is out of phase. Check all system connections and rectify.
(Read the manual for correct connection procedure)

Distorted / rattling sounds at high levels

System level too high; Objects on speakers/subwoofer; Objects too close to subwoofer

Sound lacks bass content
Bass reproduction indistinct

Front loudspeakers out of phase. Check all system connections and rectify.
Subwoofer not switched on; Subwoofer phase incorrect; Subwoofer crossover control too low

No Sound

System not switched on; Speaker cables shorting terminals out; Wrong source selected

Symptom

Possible Cause

Before investigating a problem, always switch off the system at the mains.

Loudspeaker Maintenance

Use a slightly dampened cloth to clean your cabinets and occasionally, a very light spray polish to protect their sheen. If necessary
clean grilles carefully with a soft brush. Subwoofers should only ever be cleaned with a soft dry cloth.

Never touch the loudspeaker drive units as they can be damaged by improper handling.

Product Service

Should a fault occur with your loudspeakers please return them as a pair, even if only one unit appears to be faulty. Please pack them
correctly, using the original packing.

Product for service should be returned to the appointed dealer from whom you purchased the product. If you experience difficulties or
there is no Mission dealer in your area, contact the Mission distributor for your country or the Main Service Centre for your region.

International Audio Group
Unit 4, St Margaret’s Way,
Stukeley Meadows Industrial Estate
Huntingdon, Cambs, PE29 6EB
Tel:+44 (0)1480 447700 Fax: +44 (0)1480 431767

IAG. Room 2310 - 2311, Press Building, Shennan Road C,
Shenzhen, China.
Tel: +86-755-82091200 Fax: +86-755-82091205

IAG America, Inc. 8440 154th Avenue NE,
Redmond, Washington 98052 USA
Tel: +1 425 861 3909 Fax: +1 425 861 390

Authorised Service Centres

ASIA

USA

Welcome to Mission

General Information

Unpacking Your Loudspeakers

The

series is the latest in a long line of distinguished Mission loudspeakers. These technologically advanced loudspeakers will

complement the finest electronics and décor.

ass drivers

tweeters are used throughout the range.

binding posts feature on all models. Your Mission

loudspeakers will bring you great listening

pleasure for many years.

Robust b

and precision silk

Screw fastening tri-lobe multi-way

Please read these instructions carefully before installing your loudspeakers. A few minutes studying this manual will ensure
superb performance from your loudspeaker for many years.

Please pay attention to all cautions printed on the pages marked with this symbol.

•

Carefully unpack each loudspeaker.

Retain all the packing materials so that your loudspeaker can be repacked and shipped without damage.

If you dispose of the packing,do so with regard to all recycling provisions in your area.

Warning: Be careful. Loudspeaker spikes are very sharp.

When positioning the speakers avoid piercing any electrical cables.

The and loudspeakers are supplied with the spike retainers fitted to the plinth but you will need to fit the spikes

•

Mv-6

Mv-8

Fitting Spikes

Fitting the Spikes

Adjusting the Spikes

•

Invert the loudspeaker and place the top on a soft stable surface, or place the
loudspeakers on a towel or soft cloth to protect the surface.

Screw a nut fully on to each spike but ensure the nut is not tight.

Place a washer over the spike retainer.

Screw a spike half way into each spike retainer fitted in the base of the cabinet.

Tighten the nut finger tight onto the spike retainer.

Carefully return the loudspeaker to its normal position.

Ensure that spikes do not pierce cables etc. under the carpet.

Loosen each collar slightly.

Adjust the height by screwing in or out one or more of the spikes
until the loudspeaker is stable and level.

Tighten the nut fully tight onto the spike retainer.

Warning:

Never drag a loudspeaker. W lift them clear of the floor and replace them carefully

The

and

loudspeakers are heavy.

Always get someone to help you to lift and manoeuvre the loudspeakers.

hen moving loudspeakers

Mv-6

Mv-8