Sony kdl-40xbr9 Guia De Configuração Rápida

KDL-40/46/52XBR9 EN 4-140-830-11(2)

VIDEO

OUT

COMPONENT

VIDEO OUT

DIGITAL OUT

PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO

OUT

L

R

WOOFER

COAXIAL

OPTICAL

FRONT

REAR

CENTER

S VIDEO

HDMI

OUT

AC IN

PB/CB

PR/CR

OPT IN

SAT

OPT IN

VIDEO 1

COAX IN

AUDIO IN

DVD

DVD IN

SAT IN

VIDEO 2/BD IN

OUT

AUDIO IN

AUDIO IN

FRONT R

AM

FRONT L

SUR R

SUR L

CENTER SUBWOOFER

Connect your incoming signal source (HD Cable Box, HD Satellite 

Receiver, or DVD) with HDMI or component video for the best possible 

picture quality.

If your connecting equipment has DVI output instead of the HDMI output, 

you must use a DVI-to-HDMI cable for the video and also connect an 

audio cable for the sound. If this is the case, connect the cable to  

HDMI IN 1 (input) of your TV.

■

■

Connect PC’s audio output when using an HD15 connection.

Press PC’s FUNCTION Key + Select Output to transmit to TV.

When using an HD15 connection, adjust TV’s Pitch and Phase to  

correct sharpness.

Refer to your Operating Instructions.

■

■

■
■

Cable/SAT 

(dish)

SD Cable Box or  

SD Satellite Receiver

Home Theater System

or

Coaxial

HDMI

DVI-to-HDMI

Component

Composite

Audio (L/R)

Mini-Pin Audio

Digital Optical Audio

Audio (L/R) with Mini-Pin

HD15

Blu-ray Disc/DVD

Rear of TV

Side Panel

A/V Receiver

Blu-ray Disc/DVD

HD Cable Box 

or HD Satellite 

Receiver

Rear of TV

Side Panel

*A/V Receiver

*Blu-ray Disc

SAT  

(Dish)

HD Cable Box or  

HD Satellite Receiver

*Rear of TV

Cable/ 

Antenna

Notebook PC

Splitter

Rear of TV

VCR/DVD Combo

VCR

DVD

* Signifies a BRAVIA Sync capable device.

DVD

DVD Player

31033

AMP

Receiver

52172

STB

Digital Satellite

01639

Follow the steps below to program your TV remote control. 

 

 Look for the code in the Manufacturer’s Code List (see the Operating Instructions) that 

corresponds to the equipment you would like to operate with the Sony remote control.  

If more than one code is provided, try programming the first code listed. If your equipment’s 

code is not listed, visit 

 for a more comprehensive 

list.

  

Press and hold 

, 

 or 

 simultaneously with the 

 button and release. 

When in the programming mode, the FUNCTION button blinks for approximately  

30 seconds until a code is entered.  

  

Enter the five digit code using  –  while the FUNCTION button is lit. If the code is not 

entered within 30 seconds, you must repeat step 2.

 

 Press   or   to confirm the code. If successfully programmed, the FUNCTION button 

will blink twice, if not, it blinks five times.

If you can turn your equipment on and off using the green 

POWER

 button, the programming is 

complete. If not, try the next code listed. 
Note:

In some cases, you may not be able to program your remote control. If this is the case, use 

your equipment’s remote control.

 

Any of the FUNCTION buttons can be programmed to operate other equipment regardless 

of the labeling. For example, if programmed with the correct code, a Blu-ray Disc player 

can be operated with the 

 button. This is useful if your equipment does not match any 

of the labeled buttons.

■
■

DVD

AMP

STB

TV

POWE

R

PORT 1

PORT 2

PORT 3

PORT 4

POWER

INTERNET

SAT  

(Dish)

Cable/ 

Antenna

Side Panel

Cable/ 

Antenna

Cable/Antenna

Side Panel

PC

Ethernet

* For a sample wireless bridge connection diagram see the Operating Instructions or the 

  online Reference Book.

*