Sony KDL-26S2000 Instrução De Instalação
Installing the TV
on a wall
on a wall
The TV can be installed on a wall by attaching a Wall-
Mount Bracket (sold separately).
Verify your TV’s model number and be sure to use the
bracket specified for your model only. Refer to the
Steps on this manual along with the Instructions
supplied with the SU-WL31 Wall-Mount Bracket, to
properly carry out the installation.
Mount Bracket (sold separately).
Verify your TV’s model number and be sure to use the
bracket specified for your model only. Refer to the
Steps on this manual along with the Instructions
supplied with the SU-WL31 Wall-Mount Bracket, to
properly carry out the installation.
Open the Wall-Mount Bracket package and check the
contents for all required parts along with the
Instructions.
contents for all required parts along with the
Instructions.
Refer to the Instructions for the SU-WL31.
Decide where you want to install your TV. Turn to the
back cover of this manual for the TV installation
dimensions and determine the location.
Refer to the Instructions for the SU-WL31.
back cover of this manual for the TV installation
dimensions and determine the location.
Refer to the Instructions for the SU-WL31.
Refer to the Instructions for the SU-WL31.
Sufficient expertise is required for installing this
product, especially to determine the strength of the
wall for withstanding the TV’s weight. Be sure to
entrust the attachment of this product to the wall to
Sony dealers or licensed contractors and pay
adequate attention to safety during the installation.
Sony is not liable for any damage or injury caused
by mishandling or improper installation.
product, especially to determine the strength of the
wall for withstanding the TV’s weight. Be sure to
entrust the attachment of this product to the wall to
Sony dealers or licensed contractors and pay
adequate attention to safety during the installation.
Sony is not liable for any damage or injury caused
by mishandling or improper installation.
Step 1: Checking the parts
required for the
installation
installation
Step 2: Changing the position
of the arm bases
Step 3: Deciding on the
installation location
Step 4: Installing the Plate
Unit on the wall
Before detaching the Table-Top Stand, disconnect all
the cables from the TV.
the cables from the TV.
1
Rotate the cable holder by 90 degrees, and
pull it out.
pull it out.
2
Remove the screws and detach the Table-
Top Stand from the TV.
Top Stand from the TV.
Notes
•
Lay the display face down on a stable and level surface
with the Table-Top Stand hanging over the edge of the
surface. Having the display face and the base of the
Stand on the same level surface will create an unstable
working condition and can damage the TV.
with the Table-Top Stand hanging over the edge of the
surface. Having the display face and the base of the
Stand on the same level surface will create an unstable
working condition and can damage the TV.
•
To prevent damaging the surface of the LCD display,
place the TV on a soft cloth.
place the TV on a soft cloth.
3
Align the holes on the Mounting Hook Units
with the corresponding holes on the rear of
the TV. Then secure them to the TV using
four screws (supplied with SU-WL31).
with the corresponding holes on the rear of
the TV. Then secure them to the TV using
four screws (supplied with SU-WL31).
Note
When using an electric screwdriver to tighten the screws,
the torque must be approx. 2 N
the torque must be approx. 2 N
•
m (20 kgf
•
cm).
Refer to the Instructions for the SU-WL31.
1
Connect the mains lead and cables to the
corresponding sockets on the rear of the
TV. For details on the cable connection,
refer to the Operating Instructions for your
TV.
corresponding sockets on the rear of the
TV. For details on the cable connection,
refer to the Operating Instructions for your
TV.
2
Install the TV onto the Plate Unit.
Step 5: Preparing for the
installation of the TV
Cable holder
Soft cloth
Table-Top Stand
Step 6: Installing the TV on
the Plate Unit
Mounting Hook Units
The supplied screws (+PSW5 × L16)
– 2 –
– 3 –