Toshiba 42RV535U Guia Do Utilizador
39
RV535U (E/F) Web 213:276
Chapter 6: Using the TV’s features
Adding and clearing channels and inputs in the
History List
History List
Adding channels and inputs to the History List:
As a channel or input is tuned, the Channel Browser
™
adds it to the History List and displays it on the “right
side” of the Channel Browser
side” of the Channel Browser
™
. Previously tuned
channels/inputs are “shifted” to the left, eventually
moving off the left side. Press 3 C to surf backward
through the previously tuned channels/inputs. Any
channel or input that is tuned repeatedly will not be
repeated in the History List but instead will be moved to
the end of the list on the right side of the Channel
Browser
moving off the left side. Press 3 C to surf backward
through the previously tuned channels/inputs. Any
channel or input that is tuned repeatedly will not be
repeated in the History List but instead will be moved to
the end of the list on the right side of the Channel
Browser
™
.
The Channel Browser
™
will store the following channels:
•
All channels that are tuned using the numeric buttons
on the remote control.
on the remote control.
•
All channels that are tuned for at least 5 seconds using
< or , on the remote control.
Note: Whenever an item is selected that cannot be tuned (for
various reasons), the TV will automatically tune to the
previously viewed channel or input.
various reasons), the TV will automatically tune to the
previously viewed channel or input.
Clearing channels from the History List:
•
Reconfiguring the ANT/CABLE input will clear the
History List.
History List.
Note: See page 30 for details on configuring the antenna
input.
input.
•
Once 32 channels or inputs are stored in the History
List, the oldest item will be removed from the list
when a new channel or input is tuned.
List, the oldest item will be removed from the list
when a new channel or input is tuned.
•
Turning off the TV will clear the History List.
Setting the Channel Tuning Mode
This feature allows you to choose how tuning will be
handled for analog and digital channels when the TV is
in Antenna mode.
handled for analog and digital channels when the TV is
in Antenna mode.
Note: To use this feature, the Input Configuration must be set
to Antenna (
to Antenna (
- page 30).
The channel tuning mode has three options.
Note: Digital mode will be most useful after analog channels
are shut down by the government in 2009.
are shut down by the government in 2009.
To set the Channel Tuning Mode:
1
From the Setup menu, highlight Installation and
press T. A new set of Installation menu icons will
appear.
press T. A new set of Installation menu icons will
appear.
2
Open the Terrestrial menu, highlight Channel
Tuning Mode
Tuning Mode
, press c and B b to select your
desired mode, and then press T.
Note:
• The Channel Add/Delete & Channels Block windows as well
• The Channel Add/Delete & Channels Block windows as well
as the Channel Browser ANT/CABLE list will be updated
automatically when you change the mode. Also, the History
List will be cleared, but the Favorites List will be saved.
automatically when you change the mode. Also, the History
List will be cleared, but the Favorites List will be saved.
• Even if the Channel Tuning Mode is set to Digital, analog
channel 3 will still be the default channel to prevent the initial
case where no digital channels have been found in prior
channel scans. (Channel Add/Delete will not have anything
listed until a scan is done.)
case where no digital channels have been found in prior
channel scans. (Channel Add/Delete will not have anything
listed until a scan is done.)
Tuning to the next programmed channel
To tune to the next programmed channel:
Press < or , on the remote control or TV control panel.
Note:This feature will not work unless you program channels
into the TV’s channel memory (
into the TV’s channel memory (
- page 30).
Tuning to a specific channel (programmed
or unprogrammed)
or unprogrammed)
Tuning analog channels:
Press the Channel Number (0–9) on the remote control.
For example, to select channel 125, press 1, 2, 5, then T.
For example, to select channel 125, press 1, 2, 5, then T.
Tuning digital channels:
Enter the major Channel Number (0–9) on the remote
control, followed by the dash (=) button and then the
sub-channel number. For example, to select digital
channel 125-1, press 1, 2, 5, –, 1, then T.
control, followed by the dash (=) button and then the
sub-channel number. For example, to select digital
channel 125-1, press 1, 2, 5, –, 1, then T.
Note: If a digital channel is not programmed—either through
the automatic channel scan (
the automatic channel scan (
- page 30) or the channel add/
delete function (
- page 31)—you will have to tune the RF
channel using the Physical Channel Number.
Mode
Description
Standard
Both analog and digital channels can be
tuned normally
tuned normally
Auto
(default)
(default)
Digital channels will have priority when
manually entering a channel number
using the Channel Number (0-9) on the
using the Channel Number (0-9) on the
remote control, analog channels can still
be tuned by < / , if available
Digital
Only digital channels can be tuned
(continued)
52RV535U_EN.book Page 39 Tuesday, July 22, 2008 5:25 PM