Toshiba 46SV670U Guia Do Utilizador
24
Chapter 3: Using the remote control
Using the remote control to
operate your other devices
Your TV remote control has one dedicated TV mode
and three programmable multi-brand modes: CABLE/
SAT, DVD, and VCR/PVR. The default device modes
and programmable device modes are listed below.
and three programmable multi-brand modes: CABLE/
SAT, DVD, and VCR/PVR. The default device modes
and programmable device modes are listed below.
Note: The TV remote control is preprogrammed to operate
most Toshiba devices. To operate a non-Toshiba device or
a Toshiba device that the remote control is not
preprogrammed to operate, you will need to program the
remote control. See “Programming the remote control to
operate your other devices” (at right).
most Toshiba devices. To operate a non-Toshiba device or
a Toshiba device that the remote control is not
preprogrammed to operate, you will need to program the
remote control. See “Programming the remote control to
operate your other devices” (at right).
Note: Although your new TV’s remote control includes
codes for many devices, it may not include codes for some
or all of the features on certain devices you wish to control.
If you are unable to program the TV’s remote control to
operate your device or some of the features on that device,
use the device’s remote control or the controls on the
device.
codes for many devices, it may not include codes for some
or all of the features on certain devices you wish to control.
If you are unable to program the TV’s remote control to
operate your device or some of the features on that device,
use the device’s remote control or the controls on the
device.
Programming the remote control
to operate your other devices
Device code setup
1
Find the code for your device brand in the remote
control device code table on pages 26–33. If more
than one code is listed, try each one separately until
you find one that works.
control device code table on pages 26–33. If more
than one code is listed, try each one separately until
you find one that works.
2
Press the applicable mode select button (CABLE/
SAT, DVD, or VCR/PVR), until the mode select
button blinks 3 times.
SAT, DVD, or VCR/PVR), until the mode select
button blinks 3 times.
3
While holding down E, press the five-digit device
code for your device.
code for your device.
•
If a valid code is entered, the mode select button
will blink twice.
will blink twice.
•
If an invalid code is entered, the mode select button
will blink one long blink.
will blink one long blink.
4
Point the remote control at the device and press p
to test the code.
to test the code.
•
If the device responds to the remote control, you
have entered the correct code.
have entered the correct code.
•
If the device does not respond to the remote
control, repeat steps 3 and 4 using another code.
control, repeat steps 3 and 4 using another code.
Note: After programming the remote control, make
sure all necessary keys on the TV remote control (in
addition to p) operate your device. If some keys are
not operational, repeat the device code setup using
another code (if other codes are listed for your device).
If, after trying all listed codes, the necessary keys do
not operate your device, use the device’s original
remote control.
sure all necessary keys on the TV remote control (in
addition to p) operate your device. If some keys are
not operational, repeat the device code setup using
another code (if other codes are listed for your device).
If, after trying all listed codes, the necessary keys do
not operate your device, use the device’s original
remote control.
5
To control the TV, press TV.
Note:
• Every time you change the batteries you will need to
• Every time you change the batteries you will need to
reprogram the remote control.
• Some newer VCRs respond to either of two codes.
These VCRs have a switch labeled “VCR1/VCR2.” If
your VCR has this kind of switch and does not respond
to the codes for your VCR brand, set the switch to the
other position (“VCR1” or “VCR2”) and reprogram the
remote control.
your VCR has this kind of switch and does not respond
to the codes for your VCR brand, set the switch to the
other position (“VCR1” or “VCR2”) and reprogram the
remote control.
MODE SELECT
Default device mode control (before
programming)
programming)
TV
Toshiba TV
CABLE/SAT
Toshiba Satellite receiver
DVD
Orion DVD
VCR/PVR
Toshiba VCR
MODE SELECT
Device mode control after programming
TV
Toshiba TV
CABLE/SAT
Multi-brand video/audio devices
DVD
VCR/PVR
VCR/PVR