Toshiba 46SV670U Guia Do Utilizador
37
Chapter 5: Setting up your TV
Configuring the antenna input
source for the ANT/CABLE terminal
1
From the SETUP menu, highlight ANT/CABLE In.
2
Press C or c to select the input source (Antenna or
Cable) for the ANT/CABLE input on the TV and
press O.
Cable) for the ANT/CABLE input on the TV and
press O.
Programming channels into the
TV’s channel memory
When you press < or , on the remote control or TV
control panel, your TV will stop only on the channels
you programmed into the TV’s channel memory.
Follow the steps below to program channels into the
TV’s channel memory.
control panel, your TV will stop only on the channels
you programmed into the TV’s channel memory.
Follow the steps below to program channels into the
TV’s channel memory.
Auto Tuning
Your TV can automatically detect all active channels in
your area and store them in its memory. After the
channels are programmed automatically, you can
manually add or erase individual channels in the
channel memory.
your area and store them in its memory. After the
channels are programmed automatically, you can
manually add or erase individual channels in the
channel memory.
Note:
• You must configure the ANT/CABLE input source before
• You must configure the ANT/CABLE input source before
programming channels.
• If the ANT/CABLE input is configured for
Cable, the
automatic channel programming process erases
channels that were previously programmed into the TV’s
memory.
channels that were previously programmed into the TV’s
memory.
• If the ANT/CABLE input is configured for
Antenna, the
automatic channel programming process adds newly
found channels to the existing set of programmed
channels (and does NOT erase channels that were
previously programmed into the TV’s memory.) To
remove an Antenna source channel from the memory,
you must set it to Skip.
found channels to the existing set of programmed
channels (and does NOT erase channels that were
previously programmed into the TV’s memory.) To
remove an Antenna source channel from the memory,
you must set it to Skip.
• To tune the TV to a channel not programmed in the
channel memory, you must use the Channel Number
buttons on the remote control.
buttons on the remote control.
• Programming channels when the ANT/CABLE input is
configured for
Cable will take substantially longer than
when the antenna input is configured for
Antenna. This
is normal; however, once channel programming is
finished, you should not have to repeat the
programming process again unless your Cable TV
service lineup changes significantly.
finished, you should not have to repeat the
programming process again unless your Cable TV
service lineup changes significantly.
1
Configure the ANT/CABLE input, if you have not
already done so (- left-hand column).
already done so (- left-hand column).
2
From the SETUP menu, highlight Auto Tuning.
3
A screen will appear warning that previous
programs and settings will be deleted.
programs and settings will be deleted.
4
Press T to start Auto Tuning.
The TV will automatically cycle through all the
channels, and store all active channels in the
channel memory. When Auto Tuning is finished,
press < or , to view the programmed channels.
The TV will automatically cycle through all the
channels, and store all active channels in the
channel memory. When Auto Tuning is finished,
press < or , to view the programmed channels.
Manual Tuning
After automatically programming channels into the
channel memory, you can manually enter channels if
the physical channel is known.
channel memory, you can manually enter channels if
the physical channel is known.
1
From the SETUP menu, highlight Manual Tuning
and press T.
and press T.
2
Use the Channel Numbers on the remote control to
enter the channel number (up to three-digit
number) and press T.
enter the channel number (up to three-digit
number) and press T.
If channels are found, they will be listed at the bottom
of the screen. Analog channels will be noted by an
“ATV” symbol and digital channels by a “DTV”
symbol.
of the screen. Analog channels will be noted by an
“ATV” symbol and digital channels by a “DTV”
symbol.