Netopia r3100-u Guia De Referência
F-6 User’s Reference Guide
Important notes
Even with the advantages of NAT, there are several things you should note carefully:
■
There is no formally agreed upon method among router vendors to handle an all-zeros IPCP request. The
majority of router vendors use the all-zeros IPCP request to determine when a dial-in host wants to be
assigned an IP address. Some vendors however attempt to negotiate and establish routing with an
all-zeros IP address. The Netopia R3100 will not allow routing to be established with an all-zeros IP
address and the call will be dropped with an error logged in the Device Event Histor y.
majority of router vendors use the all-zeros IPCP request to determine when a dial-in host wants to be
assigned an IP address. Some vendors however attempt to negotiate and establish routing with an
all-zeros IP address. The Netopia R3100 will not allow routing to be established with an all-zeros IP
address and the call will be dropped with an error logged in the Device Event Histor y.
■
When using NAT it is most likely that the Netopia R3100 will be receiving an IP address from a “pool” of
dynamic IP addresses at the ISP. This means that the Netopia R3100's IP presence on the Internet will
change with each connection. This can potentially cause problems with devices on the Internet attempting
to access ser vices like WWW and FTP ser vers or AURP par tners on the Netopia R3100’s local LAN
inter face. In this case, if a dynamic IP address is assigned to the WAN inter face of the Netopia R3100
each time, the administrator of the Netopia R3100 will have to notify clients wishing to access ser vices on
the Netopia R3100’s LAN inter face of the new IP address after each connection.
dynamic IP addresses at the ISP. This means that the Netopia R3100's IP presence on the Internet will
change with each connection. This can potentially cause problems with devices on the Internet attempting
to access ser vices like WWW and FTP ser vers or AURP par tners on the Netopia R3100’s local LAN
inter face. In this case, if a dynamic IP address is assigned to the WAN inter face of the Netopia R3100
each time, the administrator of the Netopia R3100 will have to notify clients wishing to access ser vices on
the Netopia R3100’s LAN inter face of the new IP address after each connection.
■
With NAT enabled, there cannot be two or more of the same types of ser vice accessible from the Internet
on the LAN inter face of the Netopia R3100. For example, there cannot be multiple FTP ser vers (Por t 23) on
the Netopia R3100's LAN inter face that can be accessible by workstations on the Internet. This is due to
the fact that within the Netopia R3100 and IP there is no way to distinguish between multiple ser vers using
the same por t, in this case por t 23.
on the LAN inter face of the Netopia R3100. For example, there cannot be multiple FTP ser vers (Por t 23) on
the Netopia R3100's LAN inter face that can be accessible by workstations on the Internet. This is due to
the fact that within the Netopia R3100 and IP there is no way to distinguish between multiple ser vers using
the same por t, in this case por t 23.
■
Fictional IP addresses may be assigned on the Netopia R3100’s LAN inter face. It is strongly recommended
that for the Netopia R3100’s LAN inter face, an IP address from the Class C address range of 192.168.X.X
be used. This is because this range is defined by the IANA as an address space that will never be routed
through the Internet and is to be used by private Intranets not attached to the Internet.
that for the Netopia R3100’s LAN inter face, an IP address from the Class C address range of 192.168.X.X
be used. This is because this range is defined by the IANA as an address space that will never be routed
through the Internet and is to be used by private Intranets not attached to the Internet.
If the address range of 192.168.X.X is not used and another range of addresses such as 100.1.1.X is
used instead, this address space can potentially overlap an address space that is owned by a user
attached to the Internet. Thus if a user on the Netopia R3100’s LAN inter face has an IP address of
100.1.1.2 while the Netopia R3100’s LAN inter face is 100.1.1.2 and the local host wishes to access a
host on the Internet with the address of 100.1.1.8, the Netopia R3100 has no way of knowing that the
200.1.1.8 address is actually on the Internet and not on its local LAN inter face, as the local LAN inter face
is assigned the IP address range of 200.1.1.1 to 200.1.1.14.
used instead, this address space can potentially overlap an address space that is owned by a user
attached to the Internet. Thus if a user on the Netopia R3100’s LAN inter face has an IP address of
100.1.1.2 while the Netopia R3100’s LAN inter face is 100.1.1.2 and the local host wishes to access a
host on the Internet with the address of 100.1.1.8, the Netopia R3100 has no way of knowing that the
200.1.1.8 address is actually on the Internet and not on its local LAN inter face, as the local LAN inter face
is assigned the IP address range of 200.1.1.1 to 200.1.1.14.
Configuration
Network Address Translation is enabled by default with the Smar tStar t configuration utility. You can toggle
Enable Address Translation to NO or YES in the Connection Profile screen in System Configuration under the IP
Profile Parameters section. NAT is enabled on a per-profile basis, so it is possible to have any combination of
NAT and non-NAT profiles. An example of enabling NAT is as follows:
Enable Address Translation to NO or YES in the Connection Profile screen in System Configuration under the IP
Profile Parameters section. NAT is enabled on a per-profile basis, so it is possible to have any combination of
NAT and non-NAT profiles. An example of enabling NAT is as follows: