Mitsubishi lt-3280 Manual Do Proprietário

24.

The TV Audio icon or A/V Receiver icon is
grayed out and not selectable.

• Select the Change setting from the Edit NetCommand menu, and
   then select the device (for example VCR).  Once the Connection
   screen is displayed, check if the audio checkbox is selected for the
   TV input and/or AVR input.
•  Verify the connections and NetCommand setup for the A/V receiver and the 

desired source device, if any.  See the instructions for item 23, previous page.

25.

Devices are grayed out in the Device Selection
menu or the PIP Selection menu.

• A recording is in progress requiring the use of Monitor Out.  Cancel
  the recording to select the device.
• Digital channels and media cards cannot display in the PIP or POP.

26.

Cannot see the A/V Receiver menu.

• The A/V Receiver is not connected to any input of the media center.  
   To check the A/V Receiver menu temporarily plug into an unused 
   input of the media center.  Then select Review from the NetCommand 
   Menu, turn the  input On to view the A/V Receiver menu.

27.

Screen is black when trying to view digital
channels or IEEE 1394 device.

•  The PerfectColor™ color balance has been incorrectly set.  Use the
    Setup menu to reset the  color balance.

28.

The REC button is not working, or, on the
Transport menu the record key is grayed out and
 not available.

• The device does not support recording, such as a DVD player. 
• Recordings can not be initiated from the Transport menu when
   using an IEEE 1394 device.  Press REC instead. The Record
   menu displays allowing setup of a recording.

29.

Excessive digital artifacts.

• The IEEE 1394 cable is too long (15 feet between devices is the
   maximum length).
• There may be a slow device in the middle of the IEEE 1394 network. 
   Move the slow devices to the end so that connections for faster
   devices do not pass through them.

30.

DVCR analog/digital problems.

• If the tape is currently playing but no picture displays, there may be a
   mismatch of the media with the display.   Press DEVICE to
   display the Device Selection menu.  Press ENTER for the DVCR
   device. If digital is selected, try analog, or if analog is selected, try
   digital.

31.

D-VHS recordings for digital cable have drop-
outs (loss of picture or sound), or no playback.

• Digital cable signals on IEEE 1394 can exceed the data rate 
   standards supported by DVCR.

32.

There is no audio and video from the IEEE 1394
 device.

• The device is not turned on - turn the device power on.
• No media (tape or disc) is inserted into the device.
• The media is blank (has no recording).
• The play command failed - Try pressing play again on the device’s
   remote control or front panel.
• The device is already in use (for example: the device is currently 
   recording).        
• The source is copy-protected or violates copy protection.
• The device’s digital video signal is not supported by the TV, such as
   DV video, common with camcorders. Use analog connections
   instead, if available.
• The device is not an audio/video device.
• Too many other devices are already communicating over IEEE 1394. 
   Remove or stop some devices and try again.

33.

The IEEE 1394 Device is not listed in the Device
Selection menu.

• The device is unchecked in the Review screen.  Select the
   NetCommand menu.  Through Review, verify the device is checked.
• The IEEE 1394 plug is disconnected or loose. 
• The IEEE 1394 Device has not been powered On.  Turn on.
• The device has not been discovered.
• The device is not an Audio/Video device.

34.

The IEEE 1394 device cannot be selected.

• The device may be busy, either recording or a peer-to-peer
   connection has been established.  Cancel the recording or         
   peer-to-peer connection.

35.

DEVICE MENU button does not display a menu.

• The IEEE 1394 device does not provide a menu.
•  The TV cannot support IEEE 1394 menus.  See page 32.