Yamaha RX-V2500 Manual Do Proprietário
69
REMOTE CONTROL FEATURES
A
D
V
ANCED
OPERA
T
ION
6
Press ENTER to set the number.
“OK” appears in the display window if setting was
successful.
“NG” appears in the display window if the setting
was unsuccessful. In this case, start over from step 3.
successful.
“NG” appears in the display window if the setting
was unsuccessful. In this case, start over from step 3.
y
If you continuously want to set up another code for another
component, press the input selector button or SELECT k/n
to select the component, then repeat steps 4 through 6.
component, press the input selector button or SELECT k/n
to select the component, then repeat steps 4 through 6.
7
Press LEARN again to exit from the setup
mode.
mode.
8
Press one of the buttons shaded below to
see if you can control your component. If you
can, the remote control code is correct.
see if you can control your component. If you
can, the remote control code is correct.
y
If the manufacturer of your component has more than one
code, try each of them until you find the correct one.
code, try each of them until you find the correct one.
• “ERROR” appears in the display window if you press a button
not indicated in the respective step, or when you press more
than one button simultaneously.
than one button simultaneously.
• The supplied remote control does not contain all possible codes
for commercially available audio and video components
(including YAMAHA components). If operation is not possible
with any of the remote control codes, program the new remote
control function using the Learn feature (see “Programming
codes from other remote controls (Learn)”) or use the remote
control supplied with the component.
(including YAMAHA components). If operation is not possible
with any of the remote control codes, program the new remote
control function using the Learn feature (see “Programming
codes from other remote controls (Learn)”) or use the remote
control supplied with the component.
• Function programmed using the learn feature take priority over
remote control code functions.
Use the Learn feature if you want to program functions
not included in the basic operations covered by remote
control codes, or an appropriate remote control code is not
available. You can program any of the buttons available in
the component control area (see page 66). The buttons can
be programmed independently for each component.
not included in the basic operations covered by remote
control codes, or an appropriate remote control code is not
available. You can program any of the buttons available in
the component control area (see page 66). The buttons can
be programmed independently for each component.
This remote control transmits infrared beams. If the other remote
control also uses infrared beams, this remote control can learn
most of its functions. However, you may not be able to program
some special signals or extremely long transmissions. (Refer to
the operating instructions for the other remote control.)
control also uses infrared beams, this remote control can learn
most of its functions. However, you may not be able to program
some special signals or extremely long transmissions. (Refer to
the operating instructions for the other remote control.)
1
Set AMP/SOURCE/TV to SOURCE.
2
Press an input selector button to select a
source component.
source component.
3
Place this remote control about 5 to 10 cm
(2 to 4 in) apart from the other remote control
on a flat surface so that their infrared
transmitters are aimed at each other.
(2 to 4 in) apart from the other remote control
on a flat surface so that their infrared
transmitters are aimed at each other.
Notes
LEARN
TRANSMIT
DTV
DVR/VCR2
VCR 1
DVD
V-AUX
CBL/SAT
MD/TAPE
CD-R
PHONO
TUNER
CD
MULTI CH IN
POWER
POWER
POWER
SYSTEM
STANDBY
AV
TV
SLEEP
INPUT MODE
A
B
CLEAR
LEARN
RE–NAME
FREQ/RDS
EON
MODE
PTY SEEK
START
REC
DISC SKIP
MACRO
ON
OFF
Programming codes from other
remote controls (Learn)
remote controls (Learn)
Note
AMP
SOURCE
TV
DTV
DVR/VCR2
VCR 1
DVD
V-AUX
CBL/SAT
MD/TAPE
CD-R
PHONO
TUNER
CD
MULTI CH IN
SLEEP
INPUT MODE
A
B
TRANSMIT
SELECT
DTV
D
VR/VCR2
VCR 1
DV
D
V
-AU
X
X
CBL/SA
T
MD/T
APE
CD-R
PHONO
TUNER
CD
MUL
TI CH IN
PO
WER
PO
WER
PO
WER
SYSTEM
ST
ANDBY
AV
TV
SLEEP
INPUT MODE
A
B
5 to 10 cm (2 to 4 in)
00_RX-V2500U_EN.book Page 69 Friday, August 20, 2004 5:20 PM