Yamaha YDP-113 Manual Do Proprietário
YDP-113
Keyboard Stand Assembly
ENGLISH
29
Keyboard Stand Assembly
CAUTION
Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accor-
dance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.
• Be sure to tighten up all screws upon completing assembly of each unit.
• To disassemble, reverse the assembly sequence given below.
dance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.
• Be sure to tighten up all screws upon completing assembly of each unit.
• To disassemble, reverse the assembly sequence given below.
Remove the following parts from the package.
1.
Attach the center panel (B) to the side
panels (C).
panels (C).
The center panel (B) is installed between the side pan-
els (C). The brackets on each end of the center panel
should face the rear of the stand assembly. Place the
square holes in the center-panel brackets over the lugs
extending from the side panels, then slide down the
center panel. Each side of the center panel is attached
using two 6
els (C). The brackets on each end of the center panel
should face the rear of the stand assembly. Place the
square holes in the center-panel brackets over the lugs
extending from the side panels, then slide down the
center panel. Each side of the center panel is attached
using two 6
×
16 mm flat-head screws.
2.
Install the main unit (A).
CAUTION
• Fingers can become pinched between the main
unit and the rear or side panels, be extra careful so
as not to drop the main unit.
as not to drop the main unit.
• Do not hold the keyboard in any position other
than the position shown in the illustration.
Place the main unit (A) on the side panels (C) with the
screws on its bottom panel (toward the rear of the main
unit) just behind the grooves in the brackets located at
the top of the side panels. Then slide the main unit for-
ward until it stops.
Align the holes in the bottom panel of the main unit
with the holes in the brackets on the side panels. (Cen-
ter the main unit to produce equal clearance on the left
and right sides, as shown in the illustration.) Then use
the four 6
screws on its bottom panel (toward the rear of the main
unit) just behind the grooves in the brackets located at
the top of the side panels. Then slide the main unit for-
ward until it stops.
Align the holes in the bottom panel of the main unit
with the holes in the brackets on the side panels. (Cen-
ter the main unit to produce equal clearance on the left
and right sides, as shown in the illustration.) Then use
the four 6
×
16 mm flat-head screws to attach the main
unit. Two screws can be attached from the front side
and two screws from the rear.
and two screws from the rear.
Have a Phillips-head (+) screwdriver ready
Assembly Parts
6
×
16 mm flat-head screws
×
8
Cord holders
×
2
Damper pedal
AC power cord
C
A
C
B
6 x 16 mm flat-head screw
C
B
NOTE
If the holes of the front side brackets are not aligned with the
screw hole, position the sides of the side panels so that they
are parallel with the side of the unit.
screw hole, position the sides of the side panels so that they
are parallel with the side of the unit.
10 cm
10 cm
C
A
A
6 x 16 mm flat-head screw
C
A
Be sure to place your
hands at least 10 cm
from either end of the
main unit when posi-
tioning it.
hands at least 10 cm
from either end of the
main unit when posi-
tioning it.