Kenwood KRF-X9070D Manual De Instruções
4
EN
Remote control operation
When the STANDBY indicator is lit, the power turns ON when you press
the RCVR PWR (receiver power) key on the remote control. When the
power comes ON, press the key you want to operate.
the RCVR PWR (receiver power) key on the remote control. When the
power comes ON, press the key you want to operate.
PTY
RCVR
PWR
6 m
• When pressing more than one remote control key successively, press the
keys securely by leaving an interval of 1 second or more between keys.
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2. When the remote-controllable distance gets shorter than before,
replace all batteries with new ones.
3. Placing the remote sensor in direct sunlight, or in direct light from a
high frequency fluorescent lamp may cause malfunction.
In such a case, change the location of the system installation to
prevent malfunction.
In such a case, change the location of the system installation to
prevent malfunction.
Before applying the power
Loading the batteries
1 Remove the cover.
2 Insert the batteries.
3 Close the cover.
• Insert four AAA-size (R03) batteries as indicated by the polarity
markings.
Preparing the remote control
Operating range (Approx.)
Remote sensor
Infrared ray system
Memory back up function
Please note that the following items will be deleted from the unit's
memory if the power cord is disconnected from the AC outlet for
approximately 1 day.
memory if the power cord is disconnected from the AC outlet for
approximately 1 day.
• Power mode.
• Input selector settings.
• Picture output.
• Speaker ON/OFF.
• Volume level.
• BASS, TREBLE, INPUT level.
• TONE ON/OFF.
• LOUDNESS ON/OFF.
• Dimmer level.
• MD/TAPE settings.
• Listen mode setting.
• Speaker settings.
• SURR : MIX ON/OFF.
• SW RE-MIX ON/OFF.
• Distance setting.
• Input selector settings.
• Picture output.
• Speaker ON/OFF.
• Volume level.
• BASS, TREBLE, INPUT level.
• TONE ON/OFF.
• LOUDNESS ON/OFF.
• Dimmer level.
• MD/TAPE settings.
• Listen mode setting.
• Speaker settings.
• SURR : MIX ON/OFF.
• SW RE-MIX ON/OFF.
• Distance setting.
• Bass peak level.
• Display mode.
• Input mode setting.
• Midnight mode setting.
• PRO LOGIC II mode setting.
• CS II mode setting.
• Broadcast band.
• Frequency setting.
• Preset stations.
• Tuning mode.
• THX mode.
• DSP mode.
• ACTIVE EQ mode.
• SPEAKER EQ mode.
• Display mode.
• Input mode setting.
• Midnight mode setting.
• PRO LOGIC II mode setting.
• CS II mode setting.
• Broadcast band.
• Frequency setting.
• Preset stations.
• Tuning mode.
• THX mode.
• DSP mode.
• ACTIVE EQ mode.
• SPEAKER EQ mode.
Unpacking
Unpack the unit carefully and make sure that all accessories are
present.
present.
FM indoor antenna (1)
AM loop antenna (1)
Remote control unit (1)
Batteries (R03/AAA) (4)
RC-R2003
PTY
If any accessories are missing, or if the unit is damaged or fails to operate,
notify your dealer immediately. If the unit was shipped to you directly,
notify your shipper immediately. Kenwood recommends that you retain
the original carton and packing materials in case you need to move or ship
the unit in the future.
Keep this manual handy for future reference.
notify your dealer immediately. If the unit was shipped to you directly,
notify your shipper immediately. Kenwood recommends that you retain
the original carton and packing materials in case you need to move or ship
the unit in the future.
Keep this manual handy for future reference.
1
2
1
2
*5341/01-09/EN
2003/03/19, 4:12 PM
4