ZyXEL g-2000 plusv2 Guia Do Utilizador
ZyXEL G-2000 Plus v2 User’s Guide
266
Chapter 24 Remote Node Configuration
24.2.2 PPPoE Encapsulation
The ZyXEL device supports PPPoE (Point-to-Point Protocol over Ethernet). You can only use
PPPoE encapsulation when you’re using the ZyXEL device with a DSL modem as the WAN
device. If you change the Encapsulation to PPPoE, then you will see the next screen. Please
see the appendix for more information on PPPoE.
PPPoE encapsulation when you’re using the ZyXEL device with a DSL modem as the WAN
device. If you change the Encapsulation to PPPoE, then you will see the next screen. Please
see the appendix for more information on PPPoE.
Figure 128 Menu 11.1 Remote Node Profile for PPPoE Encapsulation
24.2.2.1 Outgoing Authentication Protocol
Generally speaking, you should employ the strongest authentication protocol possible, for
obvious reasons. However, some vendor’s implementation includes a specific authentication
protocol in the user profile. It will disconnect if the negotiated protocol is different from that in
the user profile, even when the negotiated protocol is stronger than specified. If you encounter
a case where the peer disconnects right after a successful authentication, please make sure that
you specify the correct authentication protocol when connecting to such an implementation.
obvious reasons. However, some vendor’s implementation includes a specific authentication
protocol in the user profile. It will disconnect if the negotiated protocol is different from that in
the user profile, even when the negotiated protocol is stronger than specified. If you encounter
a case where the peer disconnects right after a successful authentication, please make sure that
you specify the correct authentication protocol when connecting to such an implementation.
24.2.2.2 Nailed-Up Connection
A nailed-up connection is a dial-up line where the connection is always up regardless of traffic
demand. The ZyXEL device does two things when you specify a nailed-up connection. The
first is that idle timeout is disabled. The second is that the ZyXEL device will try to bring up
the connection when turned on and whenever the connection is down. A nailed-up connection
can be very expensive for obvious reasons.
demand. The ZyXEL device does two things when you specify a nailed-up connection. The
first is that idle timeout is disabled. The second is that the ZyXEL device will try to bring up
the connection when turned on and whenever the connection is down. A nailed-up connection
can be very expensive for obvious reasons.
Do not specify a nailed-up connection unless your telephone company offers flat-rate service
or you need a constant connection and the cost is of no concern.
or you need a constant connection and the cost is of no concern.
The following table describes the fields not already described in
.
Menu 11.1 - Remote Node Profile
Rem Node Name= ChangeMe Route= IP
Active= Yes ISP= No
Apply Alias= None
Encapsulation= PPPoE Edit IP= No
Service Type= Standard Telco Option:
Service Name= Allocated Budget(min)= 0
Outgoing: Period(hr)= 0
My Login= Schedules=
My Password= ******** Nailed-Up Connection= No
Retype to Confirm= ********
Authen= CHAP/PAP
Session Options:
Edit Filter Sets= No
Idle Timeout(sec)= 100
Active= Yes ISP= No
Apply Alias= None
Encapsulation= PPPoE Edit IP= No
Service Type= Standard Telco Option:
Service Name= Allocated Budget(min)= 0
Outgoing: Period(hr)= 0
My Login= Schedules=
My Password= ******** Nailed-Up Connection= No
Retype to Confirm= ********
Authen= CHAP/PAP
Session Options:
Edit Filter Sets= No
Idle Timeout(sec)= 100
Press ENTER to Confirm or ESC to Cancel:
Press Space Bar to Toggle.
Press Space Bar to Toggle.