Seagate savvio 10k.1 ultra320 scsi 36gb Folheto

• Disc drives are fragile. Do not drop or jar the drive. Handle the drive only 

by the edges or frame.

• Drive electronics are sensitive to static electricity. Keep the drive in its 

antistatic container until you are ready to install it. Wear a wrist strap and 
cable connected to ground. Discharge static from all items near or that 
will contact the drive. Never use an ohmmeter on any circuit boards.

• Turn off the power to the host system during installation (not necessary if 

you are using a hot-plug backplane).

• Always use forced-air ventilation when operating the drive.
• Use caution when troubleshooting a unit that has voltages present.
• Do not disassemble the drive; doing so voids the warranty.
• Return the entire drive for depot service if any part is defective.
• Do not apply pressure or attach labels to circuit board or drive top.

See Safety and Regulatory Agency Specifications, part number 75789512.

Formatted capacity 

73.4 Gbytes

36.7 Gbytes

Total # of data blocks 

143,374,744

71,687,372

 

(88BB998h)

(445DCCCh)

Cylinders (user accessible)

51,052

51,052

Heads

4

2

Disc rotation  ± 5%

10,009 RPM

10,009 RPM

Operating voltages

+5V

+12V

+5V

+12V 

   Typical operating current (amps)

0.74

0.43

0.69

0.47

• Screwdriver and four M3 x .5 metric drive mounting screws
• Forced-air ventilation to provide adequate drive cooling
• Backplane host system or enclosure that supports SCA 80-pin connec-

tors. 

Note. To operate at LVD transfer rates, you need a backplane that sup-

ports LVD devices.

This drive can operate in single-ended (SE) or low voltage differential (LVD) 
mode. This multimode capability provides backwards compatibility so you 
can use it with or without an LVD-capable host adapter or backplane. The 
primary benefits of LVD technology include faster transfer rates and 
improved device connectivity.

Note. To operate at Ultra2 rates or faster in LVD mode, all devices on the 

same bus must be running in LVD mode. If you add any SE device to 
the bus, all devices on that bus operate in SE mode.

Caution. Do not mix LVD drives on the same bus with high voltage differ-

ential (HVD) devices—drive damage may occur.

Savvio

TM

 drives have an industry-standard 80-pin Single Connector Attach-

ment (SCA) connector. Drives with these connectors are designed to be 
installed in a host system that uses a backplane. In such systems, there are 
no cables and the drive options, including SCSI IDs, are set either through 
the host interface or on the backplane. There are no jumpers on the drive 
that you can use to set the SCSI ID or other drive options. Check your sys-
tem’s documentation to determine how to configure the drive in your partic-
ular system. The backplane must provide the SCSI termination for each 
drive.

1. Mount the drive in the carrier or tray
LC drives are designed to be attached to a carrier or tray and inserted into 
the host system without I/O or power cables. 

Savvio drives provide 4 mounting holes on the bottom of the drive, 2 mount-
ing holes on each side of the drive, and 2 mounting holes on the end of the 

drive. Refer to the host system’s documentation to determine which holes to 
use to mount the drive in the carrier or tray.

Use M3 x .5 metric screws. Do not over-tighten or force the screws.

You can mount the drive in any orientation.

2. Format the drive
The drive has been 

 formatted at the factory. You do not need to 

perform another low level format on this drive unless you decide to perform 
certain diagnostics through the host adapter. If you do decide to perform a 
low level format, do not abort the format as this is likely to make the drive 
inoperable. A low level format, with verify turned on, will typically take two 
hours.

Protect against power failure or other power interruptions during the format.

a. Turn on DC power to the host system.
b. Boot the system from a system floppy, CD, or from a previously 

installed hard disc drive if there is one.

c.

Format the drive. 

Caution. Formatting a drive erases all user data. Be sure that you under-

stand this principle before formatting any hard disc drive. It is not 
necessary to format a drive that previously has been used to 
store data, unless your intention is to erase all user data. 
Seagate

®

 is not responsible for lost user data.

Savvio disc drives are designed to operate with a variety of operating sys-
tems. Please refer to your system or host enclosure manual for information 
about formatting and setting up the drive. 

• Drive does not spin up. Ensure that the host system is supplying power 

to the drive’s SCA 80-pin connector and that the drive is fully inserted into 
the host system’s backplane connector.

• Computer does not seem to recognize the drive. Verify that the drive 

is enabled by the SCSI host adapter setup utility.

For online information about Seagate products, visit www.seagate.com or 
e-mail your disc questions to DiscSupport@Seagate.com.

If you need help installing your drive, consult your dealer first. If you need 
additional help, call a Seagate technical support specialist. Before calling, 
note your system configuration and drive model number

Africa

+1-405-324-4714

Netherlands

00 800-47324283 

Australia

1800-14-7201

New Zealand

0800-443988 

Austria

0 800-20 12 90

Norway

00 800-47324283 

Belgium

00 800-47324283

Poland

00 800-311 12 38 

China*

800-810-9668

Spain

00 800-47324283 

Denmark

00 800-47324283

Sweden

00 800-47324283 

France

00 800-47324283

Switzerland

00 800-47324283 

Germany

00 800-47324283

Singapore

800-1101-150 

Hong Kong 800-90-0474

Taiwan*

00-800-0830-1730 

Hong Kong† 001-800-0830-1730

Thailand

001-800-11-0032165 

India

1-600-33-1104

Turkey

00 800-31 92 91 40 

Indonesia

001-803-1-003-2165

United Kingdom 00 800-47324283 

Ireland

00 800-47324283

USA/Canada/

1-800 SEAGATE or 

Italy

00 800-47324283

  Latin America

  +1-405-324-4700 

Japan

0034 800 400 554

Other European 

Malaysia

1-800-80-2335

 countries

+1-405-324-4714 

Middle East +1-405-324-4714

*Mandarin 
†Cantonese

Warranty. Contact your place of purchase or our web site (www.seagate.com). 

Return Merchandise Authorization (RMA). Before returning the drive, verify that it is 
defective. Seagate Worldwide customer service centers are the only facilities autho-
rized to service Seagate drives. Contact nearest center for return procedures and trade 
regulations.

Shipping the drive
Back up the data before shipping. Seagate assumes no responsibility for data lost dur-
ing shipping or service. Shipping drive in an unapproved container voids the warranty. 
Pack the drive with original box and packing materials. Use no other materials. This 
prevents electrical and physical damage in transit.