Sonance thx lcr Manual Do Utilizador

SONANCE CINEMA

SELECT

3. The cutout for all Cinema Select speakers is 10

” (270mm) x 6

” (172mm). There also must be at least 3

” (98mm) depth within the wall

cavity for the speaker.

4. Position the included cutout template where the speaker is to be located and pencil an outline on the wall.

• If you are unsure about obstructions, drill a small hole in the center of the outline and insert a coat hanger wire into the hole to feel-around for

possible obstructions.

5. Cut the mounting hole using a keyhole or drywall saw, and run the speaker wires from the mounting hole to the amplifier location.

IMPORTANT: Consult local building codes before running speaker wires through walls.

Before Installation: IR Plug

Sonance Cinema Select speakers have a plug for installing an IR receiver into

the speaker’s front baffle (See

Figure 7). In systems where the electronics

may be placed in an inconvenient location this allows remote controls to be

aimed at the front of the room instead of at the electronics.
The knockout is in the form of a bolt and retaining nut. To remove the knock-

out, unscrew the nut (located behind the baffle, see

Figure 8) and remove the

bolt. The hole is designed to receive a Sonance SMR1 or SMR1P Surface-Mount

IR receiver. Insert the IR receiver through the front of the speaker baffle and

use the nut included with the receiver to secure it to the baffle.

OTE

: T

HE SPEAKER

’

S GRILLE MAY REDUCE THE EFFECTIVENESS OF

THE

RECEIVER

. I

F THIS OCCURS

SLIGHTLY ENLARGE THE HOLES IN

THE GRILLE THAT ARE DIRECTLY IN FRONT OF THE

RECEIVER

Installation

Sonance Cinema Select speakers feature exclusive FastMount

tabs and an integral RotoLock

mounting system for quick mounting directly into existing walls.

WARNING: THE EDGES OF FASTMOUNT TABS ARE VERY SHARP. USE CAUTION WHEN HANDLING THE SPEAKER.

1. Remove the paint plug from the speaker.
2. Run speaker wire from each speaker to the amplifier location.
3. Strip ¼” – ½” of insulation from each speaker lead. Twist the strands or tin the exposed wire with solder to ensure that there are no stray strands.

(Stray strands that touch each other can cause a short-circuit that can damage your amplifier.)

4. Push the top of each spring-loaded connector post down to open the connector and insert the exposed wires into the holes in the posts.

• The speaker’s positive post is labeled with a red dot; the negative post is labeled with a black dot. Double-check that you connected amplifier “+” to

speaker “+” and amplifier “–” to speaker “–”.

5. Make sure all the RotoLock clamps are in the full

clockwise position so that they are tucked within the

mounting hole’s border. Insert the speaker into the

hole in the wall (

Figure 9). The RotoLock system can

accommodate a maximum wall material thickness of

1¼”.

• The FastMount tabs will prevent the speaker from

falling out of the mounting hole, allowing the

installer to let go of the speaker to pick-up tools

or other items (

Figure 10).

OTE

: T

AST

OUNT TABS ARE DESIGNED

FOR ONE

TIME USE ONLY

. I

F THE SPEAKER IS

REMOVED FROM THE MOUNTING HOLE THE

AST

OUNT

TABS

WILL

DISCONNECT

AND

REMAIN INSIDE THE WALL

continued on page 6

IR Plug

F i g u r e 7 :

I R P l u g

Retaining Nut

F i g u r e 8 :

I R P l u g R e t a i n i n g N u t

FastMount

Tabs

F i g u re 9 : I n s e r t i n g t h e S p e a k e r

I n t o t h e M o u n t i n g H o le

FastMount

Tabs

F i g u r e 1 0 :

F a s t M o u n t T a b s