Viking Range veso166br Instrução De Instalação
Installation
15
14
General Information
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
appliance should be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
flammable vapors.
• Disconnect the electrical supply prior to
servicing or cleaning.
• When removing the appliance for cleaning
or service, disconnect AC power supply
and carefully remove the appliance by
pulling forward.
and carefully remove the appliance by
pulling forward.
• Electrical requirements are listed in the
product specifications under the “Electrical
& Gas Requirements” section.
& Gas Requirements” section.
• Do not obstruct the flow of combustion and
ventilation air.
Moving, Handling, and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the ovens.
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the ovens.
Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film
residues and any dust or debris before being
used, then rinsed and wiped dry. Solutions
stronger than soap and water are rarely
needed.
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film
residues and any dust or debris before being
used, then rinsed and wiped dry. Solutions
stronger than soap and water are rarely
needed.
Recommendations for Unpacking
• Products are shipped on pallets with foam
• Products are shipped on pallets with foam
footings and corrugated inner-packing and
exterior hoods.
exterior hoods.
• Products are anchored to the pallet using
metal straps that are screwed to the
bottom of the product and the pallet.
bottom of the product and the pallet.
• DO NOT remove protective packaging
until you are ready to perform the
installation.
installation.
• To remove the packaging, first remove the
staples located at the bottom perimeter of
the corrugated cover.
the corrugated cover.
• Remove the corrugated cover by lifting it
off the product and remove the inner-
packing.
packing.
• Detach the product from the metal anchor
strip by removing the attachment screw.
• If installing a warming drawer beneath the
oven or a microwave above the oven, then
it is necessary to have a minimum of 2”
spacing between the oven and the
adjacent product for ventilation purposes.
it is necessary to have a minimum of 2”
spacing between the oven and the
adjacent product for ventilation purposes.
• It is recommended that 3/4” or larger
material be utilized to create a support
platform for this appliance.
platform for this appliance.
• BE SURE that support for this appliance is
perpendicular to the front facing of the
wall or cabinet before you perform the
installation.
wall or cabinet before you perform the
installation.
• Use of a hydraulic lift is recommended for
the installation of double oven units.
• All openings in the wall behind the
appliance or in the floor under the
appliance should be sealed.
appliance should be sealed.
• Keep appliance area clear and free from
combustible materials, gasoline and other
flammable vapors.
flammable vapors.
• WARNING: DO NOT USE AN
EXTENSION CORD WITH THIS
APPLIANCE. SUCH USE MAY RESULT IN
FIRE, ELECTRICAL SHOCK OR OTHER
PERSONAL INJURY.
APPLIANCE. SUCH USE MAY RESULT IN
FIRE, ELECTRICAL SHOCK OR OTHER
PERSONAL INJURY.
CAUTION
Avoid any damage to oven vents. The vents
need to be unobstructed and open to provide
proper airflow for optimal oven performance.
CAUTION
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from the
cooling fan, contact a Viking Authorized
Service Center before continuing operation.
Failure to do so can result in damage to the
oven or surrounding cabinets.
General Information
(cont.)
Recommendations for Moving
• The appliance is heavy – use extreme care
• The appliance is heavy – use extreme care
when handling!
NOTICE
DO NOT use the handle or oven door to
lift the oven. Remove door before
installation to ensure that it is not used to
lift the unit. DO NOT lift or carry the door
by the handle.
Removing the door must be done by your
Removing the door must be done by your
dealer, a qualified licensed plumber, or
certified gas installer.
• Only proper equipment should be used to
move products.
• ALWAYS take steps to protect flooring at
the installation location when moving
products.
products.
Site Preparation
Note: It is recommended that a thorough
site inspection be conducted PRIOR to
unpacking and moving this appliance.
site inspection be conducted PRIOR to
unpacking and moving this appliance.
• WARNING: DO NOT use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit. Make sure pins are
inserted into hinges before removing door
to prevent personal injury to hands and/or
fingers. Do not lift or carry the door by
the handle.
before installation to ensure that it is not
used to lift the unit. Make sure pins are
inserted into hinges before removing door
to prevent personal injury to hands and/or
fingers. Do not lift or carry the door by
the handle.
• Confirm available access to adequate
power – see electrical requirements.
–Single oven units require a 30 amp circuit
–Double oven units require a 50 amp
–Single oven units require a 30 amp circuit
–Double oven units require a 50 amp
circuit