Viking Range veso166br Instrução De Instalação
2
General Information
1. W
WA
AR
RN
NIIN
NG
G:: The use of cabinets for storage above the appliance may result in a potential burn hazard.
Combustible items may ignite, metallic items may become hot and cause burns. If a cabinet storage is to be
provided the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5” (12.7 cm)
beyond the bottom of the cabinets.
provided the risk can be reduced by installing a rangehood that projects horizontally a minimum of 5” (12.7 cm)
beyond the bottom of the cabinets.
2. W
WA
AR
RN
NIIN
NG
G:: This appliance shall not be used for space heating. This information is based on safety
considerations.
3. All openings in the wall behind the appliance and in the floor under the appliance shall be sealed.
4. Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.
5. Do not obstruct the flow of combustion and ventilation air.
6. Disconnect the electrical supply to the appliance before servicing.
7. When removing oven for cleaning and/or service;
4. Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.
5. Do not obstruct the flow of combustion and ventilation air.
6. Disconnect the electrical supply to the appliance before servicing.
7. When removing oven for cleaning and/or service;
A. Shut off gas at main supply
B. Disconnect AC power supply
C. Disconnect gas line to the inlet pipe.
D. Carefully remove the range by pulling outward. C
B. Disconnect AC power supply
C. Disconnect gas line to the inlet pipe.
D. Carefully remove the range by pulling outward. C
CA
AU
UT
TIIO
ON
N:: Range is heavy; use care in handling.
8. Electrical Requirement
Normal grounded household current 120 volts, 60 Hz, 15 amps, single phase. (GFI ground fault outlet not
recommended for use on oven.)
recommended for use on oven.)
9. Gas Manifold Pressure
Natural gas - 5.0” W.C.P.
LP/Propane - 10.0” W.C.P.
LP/Propane - 10.0” W.C.P.
10. Flexible Connection
If the unit is to be installed with flexible couplings and/or quick disconnect fittings, the installer must use a
flexible connector of at least 1/2” ID (1.3 cm) with suitable strain reliefs and comply with national and local
codes.
flexible connector of at least 1/2” ID (1.3 cm) with suitable strain reliefs and comply with national and local
codes.
11. The misuse of oven doors (e.g. stepping, sitting, or leaning on them) can result in potential hazards and/or injuries.
12. If electrical power is not supplied or interrupted, the oven will not work. No attempt should be made to operate
12. If electrical power is not supplied or interrupted, the oven will not work. No attempt should be made to operate
the oven.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
This appliance must be electrically grounded in accordance with local codes or, in the absence of codes, with the
National Electrical Code, ANSI/NFPA 70-latest edition. Installation should be made by a licensed electrician.
National Electrical Code, ANSI/NFPA 70-latest edition. Installation should be made by a licensed electrician.
F
FO
OR
R P
PE
ER
RS
SO
ON
NA
ALL S
SA
AF
FE
ET
TY
Y,, T
TH
HIIS
S A
AP
PP
PLLIIA
AN
NC
CE
E M
MU
US
ST
T B
BE
E P
PR
RO
OP
PE
ER
RLLY
Y G
GR
RO
OU
UN
ND
DE
ED
D
The power cord on this unit is equipped with a three-prong (grounding) plug which mates with standard three-prong
(grounding) wall receptacles. If there is any doubt as to whether the wall receptacle is properly grounded, the customer
should have it checked by a qualified technician.
(grounding) wall receptacles. If there is any doubt as to whether the wall receptacle is properly grounded, the customer
should have it checked by a qualified technician.
DO NOT UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER
PLUG.
INSERTION OF UNIT
Prepare the cabinet according to the cut-out infomration. Slide the uncartoned unit to the installation location on its
shipping base. Remove the base and lift and slide the unit 2/3 of the way into the cabinet. Remove the 2 stringers
from the bottom of the unit and slide it the rest of the way into the cabinet.
shipping base. Remove the base and lift and slide the unit 2/3 of the way into the cabinet. Remove the 2 stringers
from the bottom of the unit and slide it the rest of the way into the cabinet.
CAUTION
To prevent possible damage to cabinets and cabinet finishes, use only materials and finishes that will withstand
temperature up to 190
temperature up to 190
o
F (88
o
C), and that are moisture resistant. When cabinets are covered with laminates, an
appropriate heat-resistant adhesive must be used. Consult your cabinet manufacturer for proper specifications.