Alpine CDA-9825 Guia Do Utilizador
24
-EN
About MobileHub™ Link
Connect a separately sold Junction Box and a portable
telephone (available from Nokia) to control the incoming
and outgoing calls of the portable telephone.
telephone (available from Nokia) to control the incoming
and outgoing calls of the portable telephone.
CAUTION
• Even with hands-free operation, a driver can be distracted
during telephone operation or receiving a call. For the sake of
safety, drivers are requested to refrain from operating the
telephone while driving.
safety, drivers are requested to refrain from operating the
telephone while driving.
• For the sake of safety, operations other than incoming calls
and Speed-Dial outgoing calls cannot be used.
NOTES
• If a portable telephone is connected, its address book,
incoming and outgoing history are downloaded to the
Junction Box.
Junction Box.
• Please refer to the instruction manual of the Junction BOX.
Telephone Mode ON/OFF
1
Press and hold the BAND/TEL. button for at least 2
seconds to turn ON Telephone mode.
To turn OFF, press the BAND/TEL. button.
See relevant pages for each item.
seconds to turn ON Telephone mode.
To turn OFF, press the BAND/TEL. button.
See relevant pages for each item.
NOTES
• When a portable telephone is not connected, press and hold
the BAND/TEL. button for at least 2 seconds. “NO PHONE”
is displayed for about 2 seconds, then the mode returns to the
original source mode
is displayed for about 2 seconds, then the mode returns to the
original source mode
• When the portable telephone is taken off the Junction BOX
during an incoming or outgoing call, or during a hands-free
call, the call will be treated as an ordinary one by the
portable telephone.
call, the call will be treated as an ordinary one by the
portable telephone.
• When there is an incoming call while the power of CDA-9827/
CDA-9825 is OFF, the power of CDA-9827/CDA-9825 will
turn ON automatically for a hands-free call.
turn ON automatically for a hands-free call.
• Even if the power of the portable telephone is OFF, when
CDA-9827/CDA-9825 is set to the telephone mode, the power
of the portable telephone will be turned ON.
of the portable telephone will be turned ON.
• Even if the ACC power of the vehicle is turned OFF (even if
the engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone
is possible.
disconnected, and an ordinary call by the portable telephone
is possible.
• If there is an incoming call during operation (except an
outgoing call or talking), operation mode will end and switch
to the incoming or talking mode.
to the incoming or talking mode.
MobileHub™ Link Operation(Optional)
SOURCE/
POWER
POWER
Preset buttons
(1 through 6)
(1 through 6)
BAND/
TEL.
TEL.
f
g
Rotary encoder
SEARCH
F/SETUP
-/J
9
8
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same
time from a portable telephone and CDA-9827/CDA-9825 as
malfunction can result.
time from a portable telephone and CDA-9827/CDA-9825 as
malfunction can result.
• With a Junction BOX connected outgoing, incoming, and
sending history will also be recorded in the portable
telephone.
telephone.
• While telephoning, DEFEAT is also set to ON. When the call
has finished, the unit returns to the setting which you
previously set.
previously set.
• The telephone volume can be adjusted from the CDA-9827/
CDA-9825. The volume you set during the call is memorized,
and is automatically applied again on the next call.
and is automatically applied again on the next call.
• While telephoning or receiving incoming calls, press the
DISP/TITLE
button to indicate the Network Operator
display for 5 seconds.
Incoming Calls
1
Press the :/J button to receive an incoming call.
2
Press the BAND/TEL. button to finish a call.
The telephone mode will end and return to the original
source mode.
The telephone mode will end and return to the original
source mode.
NOTES
•
When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call.
seconds of receiving the incoming call.
• The incoming call can be switched to Automatic Calling or
Manual Calling.
1. Press and hold the F/SETUP button for at least 3 seconds.
2. Select the TEL mode by pressing the g or f button.
3. Press the BAND/TEL. button to change to TEL AUTO or
2. Select the TEL mode by pressing the g or f button.
3. Press the BAND/TEL. button to change to TEL AUTO or
TEL MANU.
4. Press the F/SETUP button to return to normal mode.
• Press the BAND/TEL. button during an incoming call to
disconnect it.