Hitachi 50VS69 Guia Do Utilizador
On-Scr
een Display
Setup
Set The Inputs
Set The Power Saving
OR
Set The Closed Captions
Set The Menu Options
CableCARD Information
Set The Output Terminals
Set The Quick Start Options
Setup
Reset The Software
Move
SEL
Select
54
After the CableCARD has been successfully installed,
you can access CableCARD Information menu in the
SETUP menu of the On-Screen Display.
you can access CableCARD Information menu in the
SETUP menu of the On-Screen Display.
1.
Press the MENU button on the Remote Control to
access the Main Menu screen.
access the Main Menu screen.
Follow the instructions below to access the CableCARD
Information menu.
Information menu.
Setup
Timers
Locks
Channel Manager
Audio
Video
Move
SEL
Select
2.
Use the CURSOR PAD
to highlight SETUP in
the Main Menu and press the SELECT button.
3.
Use the CURSOR PAD
to highlight CableCARD
Information and press the SELECT button.
4.
To view the CableCARD ID and Host ID, use the
CURSOR PAD
CURSOR PAD
to highlight CableCARD Info and
press the SELECT button.
CableCARD Information
Setup
Move
SEL
Return
Select the button below to acess
CableCARD ID and Host ID.
CableCARD ID and Host ID.
Select the button below to access
CableCARD and Host Diagnostics.
CableCARD and Host Diagnostics.
CableCARD Info.
Diagnostics Info.
In order to start cable service
for this device, please contact
your cable provider
CableCARD(tm): 123-456-789-1
Host: 123-456-789-1
Data: 123-456-789-1
Unit Address: 123-456-789-1
Press EXIT to return
NOTE:
The Diagnostics Info. window is for
Service use only.
Service use only.
CableCARD Information
THINGS TO CHECK WHEN USING THE
CableCARD / CableCARD Services
CableCARD / CableCARD Services
1.
Check that the CableCARD is properly inserted in
the CableCARD slot.
the CableCARD slot.
2.
Remove the CableCARD by pressing
and pulling the CableCARD straight out.
3.
Visually inspect the CableCARD to ensure all pin-
holes are in good condition, with none blocked or
damaged.
holes are in good condition, with none blocked or
damaged.
4.
Make sure the CableCARD is re-inserted in the
correct direction, then slowly push until it is fully
seated in the slot.
correct direction, then slowly push until it is fully
seated in the slot.
5.
When the CableCARD is installed, note all screen
messages that appear (“CableCARD Installed”,
“Acquiring Data”, “CableCARD is not Installed”).
If the “CableCARD Installed” message does not
appear when card is installed, check the TV’s card
slot and CableCARD pins for obstructions or
damage.
messages that appear (“CableCARD Installed”,
“Acquiring Data”, “CableCARD is not Installed”).
If the “CableCARD Installed” message does not
appear when card is installed, check the TV’s card
slot and CableCARD pins for obstructions or
damage.
6.
If problems still remain, please contact your Cable
Service Provider.
Service Provider.
NOTES:
1.
When a CableCARD is installed, Auto
Channel scan will not be needed
because the channel list is automatically
loaded to the TV's channel memory.
Channel scan will not be needed
because the channel list is automatically
loaded to the TV's channel memory.
2. The TV will take several seconds to
detect and recognize the presence of the
CableCARD. This process must be
completed before any CableCARD
information or Channel listings is
accessed.
CableCARD. This process must be
completed before any CableCARD
information or Channel listings is
accessed.
OR