Ricoh gx3000n Guia De Configuração Rápida
2
Close the Right Front Cover.
AKR005S
Loading Paper
Loading Paper in the Paper Feed Tray
Note
❒ A4/Letter size paper is loaded here.
❒ Load A4/Letter size paper in (portrait) orienta-
tion.
Lift the output tray.
AKR009S
Pull out the paper feed tray.
AKR010S
Note
❒ Pull tray completely out. Take care not to drop it.
Squeeze the paper guide release, and
then slide the side paper guides into
position according to the paper size.
then slide the side paper guides into
position according to the paper size.
AKS011S
Note
❒ Before loading paper, make sure to squeeze the
front end paper guide and slide it to an open posi-
tion.
tion.
Load paper with the print side face
down but not over the limit mark.
down but not over the limit mark.
AKS012S
Squeeze the front end paper guide, and
then slide it to meet the edge of the pa-
per.
then slide it to meet the edge of the pa-
per.
AKS013S
Hold both sides of tray, and push it
gently in until it stops.
gently in until it stops.
AKR014S
Lower the output tray.
AKR015S
Plugging in the Power Cord
Warning
• Only connect the machine to the power source de-
scribed on this sheet.
• Avoid multi-wiring.
• Connect the power cord directly into a wall outlet and
• Connect the power cord directly into a wall outlet and
never use an extension cord.
• Do not damage, break or make any modifications to
the power cord. Do not place heavy objects on it. Do
not pull it hard nor bend it more than necessary. These
actions could cause an electric shock or fire.
Warning
• Do not plug or unplug the power cord with your hands
wet. Otherwise, an electric shock might occur.
Remove the orange tape from around
the power cord.
the power cord.
Plug the power cord fully into the wall
outlet.
outlet.
ACW049S
Press the [Power] key.
AKS008S
The printer starts feeding ink into its print-heads (tak-
ing approximately 6 minutes).
ing approximately 6 minutes).
Make sure the “Ready” message is displayed on the
control panel.
control panel.
Important
❒ Do not switch off the power of the printer during
this period. Take care that the plug is not unplugged
from the wall outlet.
from the wall outlet.
❒ You might hear a clicking sound while the print
heads are filling. This is not a malfunction. It will
stop after a while.
stop after a while.
❒ When ink feed is complete, the [Power] key stops
blinking and remains lit.
Print the configuration Page.
Press the [Menu] key.
The [Menu] screen appears.
Press the [
▲] or [▼] key to display
[List/Test Print], and then press the
[#Enter].
[#Enter].
Press the [
▲] or [▼] key to display
[Config. Page], and then press the
[#Enter].
[#Enter].
The configuration page is printed.
Switch the printer off.
For USB connection, go to 8, “Installing the Printer
Driver (USB)”.
Driver (USB)”.
For network connection, switch the printer back on,
and then go to 9, “Installing the Printer Driver (Net-
work Interface Board)”.
and then go to 9, “Installing the Printer Driver (Net-
work Interface Board)”.
Installing the Printer Driver
(USB)
(USB)
Connecting the Printer via USB
Important
❒ Do not turn the printer on until you have read how
to do so.
AKR006S
Turn on the power of the computer,
and start Windows.
and start Windows.
Remove the seal on the USB slot lo-
cated on the rear of the printer, and
then insert the USB cable's hexagonal
(type B) plug firmly into the slot.
cated on the rear of the printer, and
then insert the USB cable's hexagonal
(type B) plug firmly into the slot.
AKR174S
Note
❒ Insert the USB cable’s plug with the USB mark
facing down.
❒ Make sure that the USB cable is fully inserted.
❒ Make sure the USB cable is connected properly,
especially if the multi bypass tray is attached to
the printer, because the tray makes connecting the
cable difficult.
the printer, because the tray makes connecting the
cable difficult.
Insert the USB cable's rectangular
(type A) plug firmly into the
computer's USB slot.
(type A) plug firmly into the
computer's USB slot.
Sheet 1/2
Go to sheet 2/2.
ToscanaP1-EN_Quick_FE
12/08/2005, 10:21
2