Avocent dsi5100 Instrução De Instalação

To use a terminal or terminal emulation program:
 

1.  After mounting the appliance, connect a terminal 

or PC running terminal emulation software to the serial 
port on the back panel of the DSI5100 appliance using 
the supplied null modem cable. Configure your terminal or 
terminal emulation program as follows:

 

   

Baud rate - 38.4K

 

   

Bits per character - 8 bits

 

   

Parity - None

 

   

Stop bits - 1 stop bit

 

   

Flow control - None

 

2. On the Terminal screen, enter root as the default 

username and root as the default password.

 NOTE: The DSI5100 appliance can also be accessed using a 
standard SSH client.

 

setip
The setip command configures the network configuration of 
the DSI5100 IPMI proxy appliance. The following setup options 
display, as shown in Figure 1:
 

  setip DHCP

 

  setip IP ipaddress netmask [gateway]

 NOTE: Gateway is in brackets on the screen because it 
is optional.

NOTE: Using DHCP enables you to obtain IP address and 

Remove the DSI5100 IPMI proxy appliance from the 
packaging material and place it in the chosen location.  

Locate the power cord that came with the DSI5100 IPMI proxy 
appliance. Plug one end into the power socket on the rear of 
the DSI5100 IPMI proxy appliance. Plug the other end into an 
appropriate AC wall outlet.

Connecting a terminal (optional)

Connect a terminal or PC running terminal emulation 
software to the serial port on the back panel of the DSI5100 
IPMI proxy appliance using the supplied null modem cable. 
Set the terminal to 38.4K, 8 bits, 1 stop bit, no parity and no 
flow control.

Using UTP cable, connect the network port on the back of the 
DSI5100 IPMI proxy appliance to your LAN. 

Using the DSView management software from a DSView 
software Client, add the DSI5100 IPMI proxy appliance to the 
DSView management system with the Add Unit Wizard. See 
the DSView Installer/User Guide for detailed information.

NOTE: A DSI5100 IPMI proxy appliance may only be 

Using the DSView management software, add the target 
devices you wish to monitor with the Add IPMI BMC Wizard. 
See the DSView Installer/User Guide for detailed information.

NOTE: The DSI5100 IPMI proxy appliance supports 

Use the IPMI Viewer window to monitor IPMI appliance target 
devices. See the DSView Installer/User Guide for more information.

During normal use with DSView software, you should have no 
need to access the DSI5100 IPMI proxy appliance command 
interface. However, the DSI5100 IPMI proxy appliance 
supports five commands which can be entered by logging into 
the DSI5100 using a terminal or terminal emulation program.

To manually change the DSI5100 appliance 
network configurations:
 

1. Reboot the DSI5100 appliance by entering reboot  

 

  on the Terminal screen.

 

2. After you have rebooted the appliance, at the  

 

 

  login prompt, enter root as the username and root as  

 

  the password.

 

3. Modify DSI5100 appliance configuration settings  

 

  using the setip command.

 

4. Verify the new IP parameters by entering ifconfig.  

 

 

  The IP parameters are displayed as shown in Figure 2.

 

5. Log out of the Terminal screen by entering exit.

 

Quick Installation Guide

IPMI Proxy Appliance

Avocent, the Avocent logo, The Power of Being There and DSView are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. © 2005 Avocent Corporation. All rights reserved. 

590-461-501C 

TX

LINK

PWR
CF

RESET

1

2

3

2

1

3