Revel b15a Instrução De Instalação
The large tube and bottom
base feature wire access
holes through which speak-
er wires can be threaded and
concealed from view. Thread
the end of the speaker wire
into the pedestal through
the top hole at the rear of
the large tube and back out
through the hole at the
bottom base.
base feature wire access
holes through which speak-
er wires can be threaded and
concealed from view. Thread
the end of the speaker wire
into the pedestal through
the top hole at the rear of
the large tube and back out
through the hole at the
bottom base.
Performa Pedestal 22
Assembly Instructions
There are different size
threads on each end of the
tube(s). Make sure that the
end attached to the top
plate properly fits the
6mm x 18mm screws before
attempting to tighten. It is
not possible to attach the
wrong end to the top plate,
as the threads at the bottom
end will not fit the
6mm x 18mm screws.
threads on each end of the
tube(s). Make sure that the
end attached to the top
plate properly fits the
6mm x 18mm screws before
attempting to tighten. It is
not possible to attach the
wrong end to the top plate,
as the threads at the bottom
end will not fit the
6mm x 18mm screws.
Step 1: Locate the parts bag (packed with the stand) that
contains spikes, screws, lock nuts, Allen wrench and
hole plugs. Set all parts aside.
hole plugs. Set all parts aside.
Step 2: Begin the stand assembly by fastening the three tubes
to the top plate with three enclosed 6mm x 18mm
Phillips flat head screws. Start all screws by hand before
tightening with a screwdriver.
Phillips flat head screws. Start all screws by hand before
tightening with a screwdriver.
Step 3: Place the stand upside-down and install the
bottom base with three 8mm x 20mm hex cap screws
using the Allen wrench (included).
using the Allen wrench (included).
Step 4: With the stand upside-down as shown below, install the
spikes (from Step 1) to the bottom of the base. Thread spikes
about halfway and then use a wrench or pliers to tighten
the locking nuts. Tighten all screws again after stand is fully
assembled. Turn stand upright and adjust spikes if required.
about halfway and then use a wrench or pliers to tighten
the locking nuts. Tighten all screws again after stand is fully
assembled. Turn stand upright and adjust spikes if required.
Step 5: Place the Revel Performa M22 loudspeaker as shown onto
a carpeted surface or a soft towel. Attach the assembled stand
with four 8-32 x 3/4 Phillips flat head screws.
with four 8-32 x 3/4 Phillips flat head screws.
(3) 6mm x 18mm
flat head screws
flat head screws
(4) 8-32 x 3/4” flat
head screws
(Start All Screws By Hand
Before Tightening With
Screwdriver)
Before Tightening With
Screwdriver)
Revel Performa
Pedestal 22
(Assembled)
Bottom Base
Top Plate
Bottom Base
(1) Large Tube
(2) Smaller Tubes
Top Wire Access
Hole
Hole
Bottom Wire
Access Hole
Access Hole
Spike
Lock Nut
(3) 8mm x 20mm hex
cap screws
cap screws
Top Plate
M22 Loudspeaker
If wires are not thread-
ed through the tube,
use the plugs to seal
the wire access holes.
ed through the tube,
use the plugs to seal
the wire access holes.
3 Oak Park Drive, Bedford, MA USA 01730-0413 | Tel: 781-280-0300 | Fax: 781-280-0490 | www.revelspeakers.com | 12/03 | Part No. 352290-001
(Rear)
(Front)
(Rear)
Wire Access Hole