Revel ic6t2 Instrução De Instalação
Installation Instructions
Revel
®
Ultima Voice
™
2 Pedestal
Harman Specialty Group
3 Oak Park Drive
Bedford, MA 01730-1413
USA
Tel 781-280-0300
Fax 781-280-0490
www.revelspeakers.com
Customer Service
Tel 781-280-0300
Fax 781-280-0495 (Sales)
Fax 781-280-0499 (Service)
Revel Part No. 353273-001 | Rev 0 | 03/07
Thank you for purchasing the Voice2 Pedestal for your Revel
®
Ultima Voice
™
2 Loudspeaker. Follow
the instructions below to install the pedestal.
INSTALLATION
S t e p 1 : S e t t h e U l t i m a
Vo i c e
Vo i c e
™
2 L o u d s p e a k e r
u p s i d e d o w n o n a s o f t
non-scratch surface.
non-scratch surface.
Step 2: Remove the speaker
from its cradle by carefully
r e m o v i n g t h e t i l t
adjustment knobs, felt washers, and metal washers.
from its cradle by carefully
r e m o v i n g t h e t i l t
adjustment knobs, felt washers, and metal washers.
Note: Keep the knobs and washers together as
they’ll be re-used in Step 6.
they’ll be re-used in Step 6.
Step 3: If the combination
spikes/glides were installed
on the cradle, remove the
spikes, felt washers, and
knurled locking rings. If
the combination spikes/
glides were not installed,
continue to Step 4.
spikes/glides were installed
on the cradle, remove the
spikes, felt washers, and
knurled locking rings. If
the combination spikes/
glides were not installed,
continue to Step 4.
Step 4: Remove the feet and screws from the
cradle. Put them aside.
cradle. Put them aside.
S t e p 5 : I n s t a l l t h e
c o m b i n a t i o n s p i k e s /
g l i d e s w i t h t h e f e l t
w a s h e r s a n d k n u r l e d
l o c k i n g r i n g s t o t h e
bottom of the pedestal.
Hand-tighten the spikes
firmly, but do NOT over-
tighten.
c o m b i n a t i o n s p i k e s /
g l i d e s w i t h t h e f e l t
w a s h e r s a n d k n u r l e d
l o c k i n g r i n g s t o t h e
bottom of the pedestal.
Hand-tighten the spikes
firmly, but do NOT over-
tighten.
Note: If the combination spikes/glides were not
previously installed on the cradle, the hardware will
be with the loudspeaker hardware accessories.
previously installed on the cradle, the hardware will
be with the loudspeaker hardware accessories.
Note: Refer to the Ultima Voice™2 Loudspeaker
Owner’s Manual for further instructions on how to
install the combination spikes/glides to the bottom
of the pedestal.
Owner’s Manual for further instructions on how to
install the combination spikes/glides to the bottom
of the pedestal.
Step 6: Use the four Phillips
head screws located in the
Pedestal accessories bag to
install the cradle to the top
of the pedestal. Tighten the
screws firmly but do NOT
over-tighten.
head screws located in the
Pedestal accessories bag to
install the cradle to the top
of the pedestal. Tighten the
screws firmly but do NOT
over-tighten.
Step 7: Install the loudspeaker onto the cradle/
pedestal assembly. Insert each threaded tilt
adjustment knob first through a metal washer and
then through a felt washer before inserting it into
one of the threaded inserts toward the rear of the
loudspeaker.
pedestal assembly. Insert each threaded tilt
adjustment knob first through a metal washer and
then through a felt washer before inserting it into
one of the threaded inserts toward the rear of the
loudspeaker.
Step 8: Slide the loudspeaker in the cradle to
adjust the tilt. When the loudspeaker has been
appropriately positioned, firmly hand-tighten the
tilt adjustment knobs to lock the loudspeaker in
place. Do NOT over-tighten.
adjust the tilt. When the loudspeaker has been
appropriately positioned, firmly hand-tighten the
tilt adjustment knobs to lock the loudspeaker in
place. Do NOT over-tighten.
Front & rear tilt
adjustment threaded inserts
adjustment threaded inserts
Felt washer
Metal washer
Lockdown knob