Kicker dx200.4 Guia Do Utilizador
+
+
+
-
-
-
KUNEK
10 - COMA
10 - COMA
+12V
18"
(45cm)
24"
(60cm)
+
Installation
1. Mounting Choose a structurally sound location to mount your Kicker amplifi er. The controls on the
top of the amplifi er need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
top of the amplifi er need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to
the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery’s negative post and the vehicle chassis is recommended.
the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery’s negative post and the vehicle chassis is recommended.
The DX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low
level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er,
the DX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the
source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to
the RCA Inputs on the end panel of the amplifi er as shown in Figure 1. Keep the audio signal cable
away from factory wiring harnesses
and other power wiring. If you need
to cross this wiring, cross it at a 90
degree angle.
level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er,
the DX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the
source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to
the RCA Inputs on the end panel of the amplifi er as shown in Figure 1. Keep the audio signal cable
away from factory wiring harnesses
and other power wiring. If you need
to cross this wiring, cross it at a 90
degree angle.
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your
amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it.
See the chart below for power and ground wire size, and fusing recommendations.
amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it.
See the chart below for power and ground wire size, and fusing recommendations.
3. Confi guration The following diagrams show the most common confi gurations for your Kicker DX
series amplifi er.
series amplifi er.
TwoChannelOperation (Stereo) DX.4 series amplifi ers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
impedance of 2 ohms per channel in stereo operation. See Figure 2.
BridgedOperation (Mono) DX.4 amplifi ers are capable of operating into a minimum impedance of 4
ohms when in bridged operation. See Figure 3.
ohms when in bridged operation. See Figure 3.
StereoBridgedOperation (Simultaneously) The DX.4 series amplifi ers are capable of operating into a
minimum impedance of 4 ohms bridged and 2 ohms per channel in stereo operation. See Figure 4.
minimum impedance of 4 ohms bridged and 2 ohms per channel in stereo operation. See Figure 4.
DX.4SeriesAmplifi er
Owner’sManual
FourChannelModels: DX200.4
Authorized Kicker Dealer:
Purchase Date:
Amplifi er Model Number:
Amplifi er Serial Number:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
__________________________
__________________________
__________________________
__________________________
INST
ALLA
TION
ModelDX200.4
1 (ONE) 30 AMPERE FUSE
PowerGroundWire 8GA
2
DX.4AMPLIFIER
CONFIGURA
TION
3
Note: To get the best performance from your new Kicker Amplifi er, we recommend using genuine Kicker Accessories and Wiring.
+
-
-
+
-
+
+
-
+
+
+
KUNEK
10 - COMA
10 - COMA
+12V
18"
(45cm)
24"
(60cm)
+
+
-
-
KUNEK
10 - COMA
10 - COMA
+12V
18"
(45cm)
24"
(60cm)
Figure 2
Figure 3
Figure 4
Minimum Impedance of 2 ohms per channel in stereo operation
Minimum impedance of 4 ohms while in bridged operation
Minimum impedance of 4 ohms mono and 2 ohms
per channel in stereo simultaneously.
Ground
Remote
Turn-On
Turn-On
Fuse
Battery
Source Unit
Ground
Remote
Turn-On
Turn-On
Fuse
Battery
Ground
Remote
Turn-On
Turn-On
Fuse
Battery
Stereo Input 1
Source Unit
Source Unit
Bridge Wiring
Bridge Wiring
Bridged Operation (Mono)
Four Channel Operation (Stereo)
Stereo and Mono Operation Simultaneously (SAMS)
Stereo Input 2
Stereo Input 1
Stereo Input 2
Stereo Input 1
Stereo Input 2
Front Stereo
Output
Rear Stereo
Output
+
+
>
+
>
Core Cable
Ground or Shielding
High-level Speaker Output Wire
To Amplifi er
To Source Unit
Figure 1
2008 DX 200-4 4in1 a01.indd 3-4
2008 DX 200-4 4in1 a01.indd 3-4
1/17/2008 11:30:55 AM
1/17/2008 11:30:55 AM