Sony MEX-BT2600 Guia Do Utilizador
13
Connecting the last-connected audio
device from this unit
device from this unit
1
Be sure that both this unit and the audio device
are switched to Bluetooth signal on.
are switched to Bluetooth signal on.
2
Press (SOURCE) repeatedly until “BT
AUDIO” appears.
AUDIO” appears.
3
Press (6).
“
” flashes while the connection is being
made. And then “
” stays lit when the
connection is made.
Handsfree talking
Receiving calls
When receiving a call, a ring tone is output from
your car speakers. Check that the unit and
cellular phone are connected beforehand.
your car speakers. Check that the unit and
cellular phone are connected beforehand.
1
Press (handsfree) when a call is
received with a ring tone.
received with a ring tone.
The phone call starts.
To end a call
Press (handsfree) again, or (OFF).
To reject an incoming call, press and hold
(handsfree) for 2 seconds.
(handsfree) for 2 seconds.
Mic Gain adjustment
You can switch between two volume levels
(“LOW” or “HI”) to set a suitable level for the
other party during a call.
(“LOW” or “HI”) to set a suitable level for the
other party during a call.
1
Press (5) during a call.
The item changes as follows:
MIC-LOW
y MIC-HI
Note
The microphone of this unit is located on the rear of
the front panel (page 9). Do not cover the microphone
with tape, etc.
The microphone of this unit is located on the rear of
the front panel (page 9). Do not cover the microphone
with tape, etc.
Making calls
In the case of making calls from this unit, redial
is used.
is used.
1
Press
(SOURCE)
repeatedly until “BT
PHONE” appears.
2
Press and hold (handsfree) for 3
seconds or more.
seconds or more.
The phone call starts.
To end a call
Press (handsfree) again, or (OFF).
To call another phone, use your cellular phone,
and then transfer the call.
For call transfer details, check the following.
and then transfer the call.
For call transfer details, check the following.
Call transfer
In order to activate/deactivate the appropriate
device (this unit/cellular phone), check the
following.
device (this unit/cellular phone), check the
following.
1
Press and hold (handsfree) or use
your cellular phone.
your cellular phone.
For details on cellular phone operation, refer to
your cellular phone manual.
your cellular phone manual.
Note
Depending on the cellular phone, handsfree
connection may be cut off when call transfer is
attempted.
Depending on the cellular phone, handsfree
connection may be cut off when call transfer is
attempted.
Voice Dial Activation
You can activate voice dialing with a cellular
phone connected to this unit by saying the voice
tag stored on the cellular phone, then make a call.
phone connected to this unit by saying the voice
tag stored on the cellular phone, then make a call.
1
Press
(SOURCE)
repeatedly until “BT
PHONE” appears.
2
Press
(handsfree).
The cellular phone enters voice dialing mode.
3
Say the voice tag stored on the cellular
phone.
phone.
Your voice is recognized, and the call is
made.
made.
Notes
• Check that unit and cellular phone are connected
• Check that unit and cellular phone are connected
beforehand.
• Store a voice tag on your cellular phone beforehand.
• If you activate voice dialing with a cellular phone
• If you activate voice dialing with a cellular phone
connected to this unit, this function may not always
work in some cases.
work in some cases.
• Noises such as the engine running may interfere
with sound recognition. In order to improve
recognition, operate under conditions where noise is
minimized.
recognition, operate under conditions where noise is
minimized.
• Voice dialing may not work in some situations,
depending on the effectiveness of the cellular
phone’s recognition function. For details, see the
support site (page 23).
phone’s recognition function. For details, see the
support site (page 23).
Tips
• Speak in the same way as you did when you stored
• Speak in the same way as you did when you stored
the voice tag.
• Store a voice tag while seated in the car, via this unit
with “BT PHONE” source selected.