Arecont Vision av10005 Guia Do Utilizador
ARECONT VISION USER MANUAL
65
Arecont Vision 425 E Colorado St, 7
th
Floor Glendale, CA 91205 Revised 5/9/2010
www.arecontvision.com
www.arecontvision.com
www.arecontvision.com
www.arecontvision.com
resolution in terms of the number of pixels)some zones may not correspond to the active image area
(valid value 64)
(valid value 64)
•
mdzonesize
mdzonesize
mdzonesize
mdzonesize – size of motion detection zones measured in number of 32x32 pixel blocks in each zone;
All zones are squares of the same size from 7x7 to 15x15 (valid values are 7 to 15 for AV1300 and
AV2100 and 8 to 15 for AV3100 and AV3130)
All zones are squares of the same size from 7x7 to 15x15 (valid values are 7 to 15 for AV1300 and
AV2100 and 8 to 15 for AV3100 and AV3130)
•
mdlevelthreshold
mdlevelthreshold
mdlevelthreshold
mdlevelthreshold – motion detection threshold that determines the sensitivity to local inter-frame
brightness changes (valid values are 2…31). Lower settings may cause false motion detection due to
noise. This parameter corresponds to “Level” under the “Motion Settings” in the AV100 Video
System GUI.
brightness changes (valid values are 2…31). Lower settings may cause false motion detection due to
noise. This parameter corresponds to “Level” under the “Motion Settings” in the AV100 Video
System GUI.
•
mdsensitivity
mdsensitivity
mdsensitivity
mdsensitivity – sensitivity of the motion detection to sudden overall lighting changes. This prevents
false triggering due to a sudden overall brightness change that triggers motion detection in a large
number of zones simultaneously. If more than this number of zones have motion it is assumed that
the change is due to lighting
false triggering due to a sudden overall brightness change that triggers motion detection in a large
number of zones simultaneously. If more than this number of zones have motion it is assumed that
the change is due to lighting
change and the detected motion is ignored. Recommended values are
40 for AV3100/AV3130, 30 for AV2100 and 20 for AV1300. This parameter corresponds to “Limit”
under the “Motion Settings” in the AV Video System GUI.
under the “Motion Settings” in the AV Video System GUI.
•
mddetail
mddetail
mddetail
mddetail – allows controlling the size of detectable moving objects. The value is the number of 32x32
sub-zones within each zone that should contain motion for the entire zone to be considered to contain
motion. (valid values are 1 through square of mdzonesize
sub-zones within each zone that should contain motion for the entire zone to be considered to contain
motion. (valid values are 1 through square of mdzonesize
mdzonesize
mdzonesize
mdzonesize). This parameter corresponds to “Detail”
under “Motion Settings” in AV Video System GUI.
•
mdprivasymask
mdprivasymask
mdprivasymask
mdprivasymask – Privacy matrix. An 8-byte array, where each byte corresponds to one row of motion
detection zones. Each bit in a byte enables motion detection in a corresponding zone, if set to ‘1’.
Leftmost zone is controlled by MSB, rightmost zone by LSB.
detection zones. Each bit in a byte enables motion detection in a corresponding zone, if set to ‘1’.
Leftmost zone is controlled by MSB, rightmost zone by LSB.
Example: set?mdprivasymask=2a8f3d135b71ee04 results in the following enabled zones
relative to camera image:
relative to camera image:
01010100
11110001
10111100
11001000
11011010
10001110
01110111
00100000
•
mdresult
mdresult
mdresult
mdresult – Motion detection information returned by the camera; The return value is “no motion” if
motion has not been detected, otherwise the motion detection information is returned in the following
format:
motion has not been detected, otherwise the motion detection information is returned in the following
format:
mdresult=<SP><hexadecimal byte0><SP><hexadecimal byte1>...<SP><hexadecimal byte63>