Manualsbrain.com
  1. Manuais
  2. Marcas
  3. ONKYO
  4. dv-cp704
  5. Manual De Instruções

ONKYO dv-cp704 Manual De Instruções

Download
Página de 52
49
Troubleshooting
Symptom
Possible cause
Remedy
Can’t turn 
on the 
DV-CP704?
The power cord is not connected.
Connect the power cord to a suitable wall outlet 
(page 22).
External interference is affecting the DV-CP704’s dig-
ital circuitry.
Turn off the DV-CP704, wait five seconds, then try turning 
it on again. If that fails, disconnect the power cord from the 
wall outlet, wait 10 seconds, reconnect it, then try turning it 
on again.
No picture?
The wrong input source is selected on your TV.
On your TV, select the input to which the DV-CP704 is 
connected (page 22).
The video cable is not connected properly.
Check the video cable and correct as necessary (page 18).
No HDMI Video Output?
The HDMI Output Setting is set to Off.
Try pressing the [RESOLUTION] button on the remote 
controller repeatedly to switch the HDMI OUT on, and 
then pressing the [RESOLUTION] button repeatedly to 
get picture (page 39).
Your TV doesn’t support HDMI Resolution settings of 
720p and 1080i.
No Component Video Output?
Your TV does not support progressive scanning, and 
the HDMI OUT is on.
Press and hold down the remote controller’s [RESOLU-
TION] button to turn off the HDMI OUT (page 39). 
Make sure the PRGV indicator is not on.
While the HDMI OUT is on, the component video out-
put outputs progressive video.
Press and hold down the remote controller’s [RESOLU-
TION] button to turn off the HDMI OUT, and then set the 
progressive Setting on the onscreen setup menus to Inter-
laced (page 39, 44). Make sure the PRGV indicator is not 
on.
The HDMI Resolution is not set to 480p (480p/576p).
Press the remote controller’s [RESOLUTION] button 
repeatedly to change the resolution (page 39).
Press and hold down the remote controller’s [RESOLU-
TION] button to turn off the HDMI OUT, and then set the 
progressive Setting on the onscreen setup menus to Inter-
laced (page 39, 44). Make sure the PRGV indicator is not 
on.
No S-Video or Composite Video Output?
The HDMI Resolution is not set to 480p (480p/576p).
Try pressing the [RESOLUTION] button on the remote 
controller repeatedly to get picture (page 39).
No sound?
The wrong input source is selected on your hi-fi amp 
or AV receiver.
On your hi-fi amp or AV receiver, select the input to 
which the DV-CP704 is connected (page 19).
The audio cable is not connected properly.
Check the audio cable and correct as necessary 
(page 18–20).
The hi-fi amp or AV receiver connected to the 
DV-CP704’s audio outputs is not on.
Turn on the hi-fi amp or AV receiver.
The Digital/HDMI Audio Out setting is incorrect.
Check the Digital/HDMI Audio Out setting and correct as 
necessary (page 45).
No Sound from the HDMI OUT?
The Digital/HDMI Audio Out setting is set to Off.
Change the Digital/HDMI Audio Out setting to either All 
or PCM (page 45).
The DVD player is connected to the DVI jack on your 
TV or AV receiver.
You won’t hear any sound from the HDMI output if the 
source component is only DVI/HDCP-Compatible 
(page 45).
The HDMI setting on your TV or AV receiver is set to 
DVI.
Change the HDMI setting on your TV or AV receiver to 
HDMI (page 45).
Your TV or AV receiver doesn’t support Dolby Digital.
Change the Digital/HDMI Audio Out setting to PCM 
(page 45).
Your TV or AV receiver doesn’t support DTS.
The DV-CP704 will not be able to play DTS format audio 
or soundtracks. On your DVD-Video disc’s audio setup 
menu, select an audio format other than DTS.
Your TV or AV receiver doesn’t support 96 kHz PCM.
Change the Linear PCM Out setting to Down Sample On 
(page 45).