ONKYO ht-s870 Manual De Instruções
49
Advanced Setup
—Continued
With this function you can adjust the volume of each
speaker so that all speakers can be heard equally at the
listening position.
speaker so that all speakers can be heard equally at the
listening position.
Notes:
• Since the HT-R820THX supports THX, the test
• Since the HT-R820THX supports THX, the test
tone is output at the standard level of 0 dB (abso-
lute volume setting 62). If you normally listen at
volume settings below this, be careful because the
test tone will be much louder.
lute volume setting 62). If you normally listen at
volume settings below this, be careful because the
test tone will be much louder.
• The volume cannot be adjusted while the speaker lev-
els are being set.
Note:
• This procedure can also be performed by using the
remote controller. First press the [TEST TONE] but-
ton to output the test tone. Use the [LEVEL–] and
[LEVEL+] buttons to adjust the levels, and use the
[CH SEL] button to select the speakers.
ton to output the test tone. Use the [LEVEL–] and
[LEVEL+] buttons to adjust the levels, and use the
[CH SEL] button to select the speakers.
When using a handheld sound level meter, calibrate each
speaker channel to 75 dB SPL at the seating position,
measured with C-weighting and slow reading.
speaker channel to 75 dB SPL at the seating position,
measured with C-weighting and slow reading.
Speaker Levels
1
Press the [AMP] button followed
by the [SETUP] button on the
remote controller.
by the [SETUP] button on the
remote controller.
Speaker levels cannot be set while the
HT-R820THX is muted, headphones are con-
nected, Speaker B is on, or the multichannel
input is being used.
HT-R820THX is muted, headphones are con-
nected, Speaker B is on, or the multichannel
input is being used.
CD
+10
0
CLEAR
1
2
3
4
5
6
7
8
9
V1
V2
V3
DVD
MULTI CH
--/---
TAPE
TUNER
INPUT
I
+
-
ENTER
SET
UP
GUI
DE
RE
TURN
EXIT
Re-EQ
LEVEL
-
LEVEL
+
CH SEL
TEST TONE
DSP
DIRECT
STEREO
ALL ST
THX
SURR
L NIGHT
TO
P M
ENU
MEN
U
VOL
+
-
CDR
SAT
AMP
+
_
TV
VCR
CABLE
DVD
CD
MD
DISC
CH
TONE
TUNER/
TAPE
TAPE
DISPLAY
TV
INPUT
INPUT
PREV
CH
CH
DIMMER
SLEEP
RANDOM
SP A
SP B
MUTING
ANGLE
SEARCH
SUBTITLE
AUDIO
MEMORY
A-B
REPEAT
ON
STANDBY
T V
TV CH
T V VOL
RC-571M
REC
LAST M
REMOTE MODE
OPEN/CLOSE
DSP
VIDEO OFF
OR-EQ
LEVEL
-
LEVEL
+
SETUP
ENTER
AMP
2
Use the Up and Down [
]/[
]
buttons to select “3. Level Cal,”
and then press the [ENTER] but-
ton.
and then press the [ENTER] but-
ton.
A pink noise test tone is output by the
front left speaker.
front left speaker.
3
Use the Left and Right [
]/[
]
buttons to adjust the speaker
level, and use the Down [
level, and use the Down [
] but-
ton to select the next speaker.
The level can be adjusted from –12 to
+12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
+12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
4
Repeat step 3 so that the level of
the test tone from each speaker
is the same.
the test tone from each speaker
is the same.
Speakers that you set to No or None in
the Speaker Configuration (page 50) do
not output the test tone.
the Speaker Configuration (page 50) do
not output the test tone.
5
Press the [SETUP] button.
Setup closes.
Don’t forget to turn down the volume if
you turned it up while setting the levels.
Don’t forget to turn down the volume if
you turned it up while setting the levels.
ENTER
ENTER
ENTER
ENTER
HT-S870_En.book Page 49 Monday, September 13, 2004 5:15 PM