ONKYO ht-s7100 Guia Do Utilizador
31
Connecting Your Components
—Continued
■
Video Signals
Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.
Composite video, S-Video, and component video sources can be upconverted for the HDMI output. See “Video Con-
nection Formats” on page 22 for more information.
Composite video, S-Video, and component video sources can be upconverted for the HDMI output. See “Video Con-
nection Formats” on page 22 for more information.
■
Audio Signals
Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV
receiver. Normally, they are not output by the HDMI OUT, unless the Audio TV Out setting is set to On (see page 81).
receiver. Normally, they are not output by the HDMI OUT, unless the Audio TV Out setting is set to On (see page 81).
To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the Audio TV Out
setting to On (see page 81), and set your DVD player’s HDMI audio output setting to PCM.
setting to On (see page 81), and set your DVD player’s HDMI audio output setting to PCM.
Notes:
• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can
be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need
to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In
addition, video signals from a PC are not supported.
to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In
addition, video signals from a PC are not supported.
• When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be
seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV
power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound
may be cut off.
power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound
may be cut off.
• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the
picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected
component’s instruction manual for details.
component’s instruction manual for details.
Making HDMI Connections
Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV,
projector, and so on.
projector, and so on.
Hint!
R
L
PRE OUT
ZONE 2
LINE OUT
ANTENNA
FM
AM
75
REMOTE
CONTROL
COAXIAL
OPTICAL
1
(DVD)
2
(CBL/SAT)
1
(GAME/TV)
2
(CD)
DIGITAL IN
ASSIGNABLE
IN 1(DVD)
IN 2
COMPONENT VIDEO
Y
C
B/
P
B
C
R/
P
R
ASSIGNABLE
HDMI
IN 1
IN 2
IN 3
IN 4
ASSIGNABLE
L
R
L
R
SURR BACK SPEAKERS
SURR SPEAKERS
FRONT SPEAKERS
CENTER SPEAKER
Bi-AMP for FRONT SPEAKERS
R
L
R
L
IN
IN
IN
IN
IN
IN
IN
IN
IN
SUB
WOOFER
FRONT
SURR
SURR BACK
CENTER
CBL/SAT
GAME/TV
GAME/TV CBL/SAT
VCR/DVR
VCR/DVR
DVD
TAPE
CD
DVD
MONITOR
OUT
S
V
S
V
(DVD)
(GAME/TV)
(CBL/SAT)
(VCR/DVR)
SUB
WOOFER
OUT
OUT
OUT
OUT
OUT
HDMI
IN
HDMI
OUT
IN 1
(DVD)
OUT
DVD player
TV
HT-S7100_En.book Page 31 Friday, July 11, 2008 10:36 AM