ONKYO ht-s9100thx Manual Do Utilizador

 

90

 

■

 

This setting determines whether audio received by an 
HDMI input is output by the HDMI OUT. You may want 
to change this setting to On if your TV is connected to an 
HDMI OUT and you want to listen to audio from an 
HDMI component through your TV’s speakers. Nor-
mally, it should be set to Off.

 

 HDMI audio is not output (default).

 

 HDMI audio is output.

 

• If On is selected and the signal can be output by the 

TV, the AV receiver will output no sound through its 
speakers.

• When TV Control is enabled, this setting is set to 

Auto.

• With some TVs and input signals, no sound may be 

output even if On is selected.

• When the Audio TV Out setting is set to On, or TV 

Control is set to Enable and you’re listening through 
your TV’s speakers (see page 35), if you turn up the 
AV receiver’s volume control, the sound will be output 
by the AV receiver’s speakers. To stop the AV 
receiver’s speakers producing sound, change the set-
tings, change your TV’s settings, or turn down the AV 
receiver’s volume.

 

■

 

The Lip Sync function can automatically synchronize 
HDMI audio and video that’s gotten out of sync due to 
the complex digital video processing being performed by 
your HDMI-compatible TV. With HDMI Lip Sync, the 
audio delay required to synchronize the audio and video 
is calculated and applied automatically by the AV 
receiver. 

 

HDMI lip sync disabled.

 

  HDMI lip sync enabled.

 

• This function works only if your HDMI-compatible 

TV supports HDMI Lip Sync.

• You can check the amount of delay being applied by 

the HDMI Lip Sync function on the A/V Sync screen 
(see page 86).

 

■

 

If your HDMI source and HDMI-compatible TV both 
support x.v.Color, you can enable x.v.Color on the AV 
receiver with this setting.

 

  x.v.Color disabled.

 

  x.v.Color enabled.

 

■

 

This function allows RIHD-compatible components 
connected via HDMI to be controlled with the AV 
receiver.

 

RIHD disabled.

 

RIHD enabled.

 

• RIHD, which stands for Remote Interactive over 

HDMI, is the name of the system control function 
found on Onkyo components. The AV receiver can be 
used with CEC (Consumer Electronics Control), 
which allows system control over HDMI and is part of 
the HDMI standard. CEC provides interoperability 
between various components, however, operation with 
components other than RIHD-compatible components 
and recommended components cannot be guaranteed.

• Select Disable if a connected component is incompat-

ible or you’re not sure about its compatibility.

• If operation is unreliable when set to Enable, select 

Disable instead.

 

To link the power functions of RIHD-compatible com-
ponents connected via HDMI, select Enable.

 

 Power Control disabled.

 

Power Control enabled.

 

• The Power Control setting can be set only when the 

above Control setting is set to Enable.

• HDMI power control only works with RIHD-compat-

ible components that support it and may not work 
properly with some components due to their settings 
or compatibility.

• When set to Enable, the AV receiver consumes more 

power.

• When set to Enable, the AV receiver enters Ready 

mode when set to Standby, and the STANDBY indica-
tor lights up.

• When set to Enable, regardless of whether the AV 

receiver is On or on Standby, both audio and video 
received by an HDMI input will be output by the 
HDMI OUT for playback on your TV or other compo-
nent that’s connected to the HDMI OUT.

HT-S9100THX_En.book Page 90 Friday, June 27, 2008 4:00 PM