ONKYO ht-s5600 Guia Do Utilizador
Controlling Other Components
En-53
Controlling Other
Components
Components
You can use the AV receiver’s remote controller to control
your other AV components, including those made by other
manufacturers. This section explains how to enter the
remote control code for a component that you want to
control: DVD, TV, CD, etc.
your other AV components, including those made by other
manufacturers. This section explains how to enter the
remote control code for a component that you want to
control: DVD, TV, CD, etc.
The following REMOTE MODE butttons are
preprogrammed with remote control codes for controlling
the components listed. You do not need to enter a remote
control code to control these components.
For details on controlling these components, see the
indicated pages.
preprogrammed with remote control codes for controlling
the components listed. You do not need to enter a remote
control code to control these components.
For details on controlling these components, see the
indicated pages.
You’ll need to enter a code for each component that you
want to control.
want to control.
Note
• Though the provided remote control codes are correct at the time
of release, they are subject to change.
You can change the configuration of colored buttons, with
which REMOTE MODE buttons are preset.
which REMOTE MODE buttons are preset.
Tip
• To reset the REMOTE MODE buttons to their default settings,
Note
• If any other button than the colored buttons is pressed, the
operation will be cancelled.
• This operation cannot be done while the AV receiver is in
Receiver mode or when Zone 2 is active.
Preprogrammed Remote Control
Codes
Codes
BD/DVD Onkyo Blu-ray Disc player (
)
TV/CD
Onkyo CD player (
Entering Remote Control Codes
1
Look up the appropriate remote control code in the
separate Remote Control Codes list.
separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).
player, TV, etc.).
2
While holding down the
REMOTE MODE button to
which you want to assign a code, press and hold
down
down
DISPLAY (about 3 seconds).
The remote indicator lights.
Note
• Remote control codes cannot be entered for RECEIVER
and the multi zone button.
• Only TV remote control codes can be entered for TV.
• Except for RECEIVER, TV, and the multi zone button,
• Except for RECEIVER, TV, and the multi zone button,
remote control codes from any category can be assigned for
the REMOTE MODE buttons. However, these buttons also
work as input selector buttons, so choose a REMOTE
MODE button that corresponds with the input to which you
connect your component. For example, if you connect your
CD player to the CD input, choose TV/CD when entering its
remote control code.
the REMOTE MODE buttons. However, these buttons also
work as input selector buttons, so choose a REMOTE
MODE button that corresponds with the input to which you
connect your component. For example, if you connect your
CD player to the CD input, choose TV/CD when entering its
remote control code.
3
Within 30 seconds, use the number buttons to enter
the 5-digit remote control code.
The remote indicator flashes twice.
If the remote control code is not entered successfully,
the remote indicator will flash once slowly.
the 5-digit remote control code.
The remote indicator flashes twice.
If the remote control code is not entered successfully,
the remote indicator will flash once slowly.
Remapping Colored Buttons
1
While holding down the
REMOTE MODE button
that you want to program, press and hold down
A
(Red) until the remote indicator lights (about 3
seconds).
You can only change colored buttons for components
whose codes belong to categories of the Remote
Control Codes list (BD/DVD player, TV, cable set-top
box, etc).
seconds).
You can only change colored buttons for components
whose codes belong to categories of the Remote
Control Codes list (BD/DVD player, TV, cable set-top
box, etc).
2
Within 30 seconds, press the colored buttons in the
order that you want to reassign them.
The button presses are assigned to each button from
left to right. The remote indicator flashes twice,
indicating that the sequence has been successfully
assigned. If the sequence is not successfully assigned,
the remote indicator will flash once slowly.
order that you want to reassign them.
The button presses are assigned to each button from
left to right. The remote indicator flashes twice,
indicating that the sequence has been successfully
assigned. If the sequence is not successfully assigned,
the remote indicator will flash once slowly.