ONKYO TX-NR3007 Guia Do Utilizador
58
Powered Zone 2/3
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
2
Use the Up and Down [
q]/[w] but-
tons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
3
Use the Up and Down [
q]/[w] but-
tons to select “1. Speaker Set-
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
4
Use the Up and Down [
q]/[w] but-
tons to select “Speaker Imped-
ance”, and then use the Left and
Right [
ance”, and then use the Left and
Right [
e]/[r] buttons to select:
4ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
less than 6.
6ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
16 ohms.
Note:
When bridging is used, “Speaker
Impedance” setting is fixed at
“8ohms”.
When bridging is used, “Speaker
Impedance” setting is fixed at
“8ohms”.
5
Use the Up and Down [
q]/[w] but-
tons to select “Speakers
Type(FrontA)”, and then use the
Left and Right [
Type(FrontA)”, and then use the
Left and Right [
e]/[r] buttons to
select:
Normal: Select this if you’ve con-
nected your front speakers A
normally.
normally.
Bi-Amp: Select this if you’ve con-
nected your front speakers A
for bi-amped operation.
for bi-amped operation.
BTL: Select this if you’ve con-
nected your front speakers A
for bridged operation. The
BTL indicator will appear on
the display.
for bridged operation. The
BTL indicator will appear on
the display.
2. Speaker
Setup
1. Speaker
Settings
2. Speaker
Configuration
3. Speaker
Distance
4. Level
Calibration
5. Equalizer
Settings
6. THX Audio Setup
2–1. Speaker
Settings
Speaker Impedance
Speakers Type(FrontA)
Speakers Type(FrontB)
Powered Zone2
Powered Zone3
Speakers Type(FrontA)
Speakers Type(FrontB)
Powered Zone2
Powered Zone3
6ohms
Normal
Not Use
Not Act
Not Act
Not Act
Notes:
• “Bi-Amp” and “BTL” cannot be
• “Bi-Amp” and “BTL” cannot be
selected if “Speakers Type(FrontB)”
is set to “Bi-Amp” or “BTL”.
is set to “Bi-Amp” or “BTL”.
• Surround back speakers and
Powered Zone 3 cannot be used if
you select “Bi-Amp” or “BTL”.
you select “Bi-Amp” or “BTL”.
6
Use the Up and Down [
q]/[w] but-
tons to select “Speakers
Type(FrontB)”, and use the Left
and Right [
Type(FrontB)”, and use the Left
and Right [
e]/[r] buttons to
select:
Not Use: Select this if you’re not using
speakers B.
Normal: Select this if you’ve con-
nected your front speakers B
normally.
normally.
Bi-Amp: Select this if you’ve con-
nected your front speakers B
for bi-amped operation.
for bi-amped operation.
BTL: Select this if you’ve con-
nected your front speakers B
for bridged operation. The
BTL indicator will appear on
the display.
for bridged operation. The
BTL indicator will appear on
the display.
Notes:
• “Bi-Amp” and “BTL” cannot be
• “Bi-Amp” and “BTL” cannot be
selected if “Speakers Type(FrontA)”
is set to “Bi-Amp” or “BTL”.
is set to “Bi-Amp” or “BTL”.
• Front high speakers, front wide
speakers and Powered Zone 2 cannot
be used if you select other than “Not
Use”.
be used if you select other than “Not
Use”.
• Surround back, front high, and front
wide speakers and Powered Zone 3
cannot be used if you select
“Bi-Amp” or “BTL”.
cannot be used if you select
“Bi-Amp” or “BTL”.
7
Press the [SETUP] button.
The setup menu closes.
The setup menu closes.