ONKYO TX-NR801 Manual De Instruções
27
Connecting the Power
• Before you plug in the TX-NR801/TX-NR801E, con-
firm that all connections have been made properly.
• Turning on the power may cause a momentary power
surge, which might interfere with other electrical
equipment on the same circuit, such as computers. If
this happens, use a wall outlet on a different circuit.
equipment on the same circuit, such as computers. If
this happens, use a wall outlet on a different circuit.
(All models other than USA, Canadian and Austra-
lian models)
lian models)
• The TX-NR801/TX-NR801E is shipped with the
main power (POWER) switch in the on position
(
(
). When the power cord is plugged in for the
first time, the TX-NR801/TX-NR801E will automati-
cally enter the standby state and the STANDBY indi-
cator will light (same condition after step 2 below).
cally enter the standby state and the STANDBY indi-
cator will light (same condition after step 2 below).
Before you can use the remote controller, you must
perform steps 1 and 2 above and place the TX-NR801/
TX- NR801E in the standby state.
perform steps 1 and 2 above and place the TX-NR801/
TX- NR801E in the standby state.
Memory backup
The TX-NR801/TX-NR801E uses a battery-less mem-
ory backup system in order to retain radio presets and
other settings when it is unplugged or in the case of a
power failure. Although no batteries are required, the
TX-NR801/TX-NR801E must be plugged into an AC
outlet in order to charge the backup system.
(On other than USA, Canadian and Australian models,
the TX-NR801/TX-NR801E’s POWER switch must be
set to ON in order to charge the backup system.) Once it
has been charged, the TX-NR801/TX-NR801E will
retain the settings for several weeks, although this
depends on the environment and time will be shorter in
humid climates.
ory backup system in order to retain radio presets and
other settings when it is unplugged or in the case of a
power failure. Although no batteries are required, the
TX-NR801/TX-NR801E must be plugged into an AC
outlet in order to charge the backup system.
(On other than USA, Canadian and Australian models,
the TX-NR801/TX-NR801E’s POWER switch must be
set to ON in order to charge the backup system.) Once it
has been charged, the TX-NR801/TX-NR801E will
retain the settings for several weeks, although this
depends on the environment and time will be shorter in
humid climates.
DSP
A-FO RM LISTENING MODE MEMORY
THX
SURROUND
DIRECT / PURE AUDIO
STEREO
FM MODE
MEMORY
ENTER
RE TURN
SETUP
TUNING
PRESET
DSP
A-FO RM LISTENING MODE MEMORY
THX
SURROUND
DIRECT / PURE AUDIO
STEREO
FM MODE
MEMORY
ENTER
RE TURN
SETUP
TUNING
PRESET
ON
RCVR
STANDBY
STANDBY/ON
STANDBY/ON
POWER
(USA, Canadian and Australian models)
(Other models)
STANDBY indicator
STANDBY indicator
To wall outlet
To wall outlet
Turning on the Power
1
Plug the power cord into an AC
wall outlet.
wall outlet.
(USA, Canadian and Australian
models)
models)
The STANDBY indicator will light up.
(Other models)
Press the POWER switch to set the
TX-NR801/TX-NR801E to standby
state.
TX-NR801/TX-NR801E to standby
state.
The STANDBY indicator will light up.
2
Press the STANDBY/ON button to
turn on the TX-NR801/TX-NR801E.
turn on the TX-NR801/TX-NR801E.
The display will light up and the
STANDBY indicator will turn off.
If you press the STANDBY/ON button
again, the TX-NR801/TX-NR801E
returns to the standby state.
STANDBY indicator will turn off.
If you press the STANDBY/ON button
again, the TX-NR801/TX-NR801E
returns to the standby state.
ON
STANDBY
OFF
ON
POWER
STANDBY
STANDBY/ON
STANDBY
Turn off
Turning on the Power from the
Remote Controller
Remote Controller
1
Press the RCVR MODE button.
The RCVR MODE button lights.
2
Press the ON button to turn on the
TX-NR801/TX-NR801E (take it out
of the standby state).
TX-NR801/TX-NR801E (take it out
of the standby state).
To return the TX-NR801/TX-NR801E
to the standby state, press the
STANDBY button.
to the standby state, press the
STANDBY button.