ONKYO TX-SA705 Guia Do Utilizador
23
Connecting the AV Receiver/AV Amplifier
—Continued
Speaker Connection Precautions
Read the following before connecting your speakers:
• North American models: Only connect speakers
• North American models: Only connect speakers
with an impedance of 6 ohms or higher. If you use
speakers with a lower impedance, and use the ampli-
fier at high volume levels for a long period of time, the
built-in protection circuit may be activated.
speakers with a lower impedance, and use the ampli-
fier at high volume levels for a long period of time, the
built-in protection circuit may be activated.
• Other models: You can connect speakers with an
impedance of between 4 and 16 ohms. If the imped-
ance of any of the connected speakers is 4 ohms or
more, but less than 6 ohms, be sure to set the minimum
speaker impedance to “4 ohms” (see page 46). If you
use speakers with a lower impedance, and use the
amplifier at high volume levels for a long period of
time, the built-in protection circuit may be activated.
ance of any of the connected speakers is 4 ohms or
more, but less than 6 ohms, be sure to set the minimum
speaker impedance to “4 ohms” (see page 46). If you
use speakers with a lower impedance, and use the
amplifier at high volume levels for a long period of
time, the built-in protection circuit may be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive
(+) terminals, and negative (–) terminals only to nega-
tive (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
(+) terminals, and negative (–) terminals only to nega-
tive (–) terminals. If you get them the wrong way
around, the sound will be out of phase and will sound
unnatural.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• If you use 4 or 5 speakers, connect each of the two
surround speakers to the SURR SPEAKERS termi-
nals. Do not connect them to the SURR BACK
SPEAKERS terminals.
nals. Do not connect them to the SURR BACK
SPEAKERS terminals.
• Be careful not to short the
positive and negative wires.
Doing so may damage the AV
receiver/AV amplifier.
Doing so may damage the AV
receiver/AV amplifier.
• Make sure the metal core of the
wire does not have contact with
the AV receiver/AV amplifier’s
rear panel. Doing so may dam-
age the AV receiver/AV amplifier.
the AV receiver/AV amplifier’s
rear panel. Doing so may dam-
age the AV receiver/AV amplifier.
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver/AV
amplifier.
amplifier.
• Don’t connect one speaker to several terminals.
Connecting the Speaker Cables
The following illustration shows which speaker should
be connected to each pair of terminals.
If you’re using only one surround back speaker, connect
it to the left (L) SURR BACK SPEAKERS terminals.
be connected to each pair of terminals.
If you’re using only one surround back speaker, connect
it to the left (L) SURR BACK SPEAKERS terminals.
1
Strip about 5/8" (15 mm)
of insulation from the
ends of the speaker
cables, and twist the bare
wires tightly, as shown.
of insulation from the
ends of the speaker
cables, and twist the bare
wires tightly, as shown.
2
Unscrew the terminal.
3
Fully insert the bare
wires.
wires.
4
Screw the terminal tight.
5/8" (15 mm)
Surround
back left
speaker
back left
speaker
Surround
back right
speaker
back right
speaker
Center
speaker
speaker
Front left
speaker
speaker
Front right
speaker
speaker
Surround
right
speaker
right
speaker
Surround
left
speaker
left
speaker
TX-SR705_En.book Page 23 Monday, May 28, 2007 2:13 PM