Bunn H5E Guia Do Utilizador
5
INITIAL SET-UP
CAUTION - The dispenser must be disconnected from the power source
throughout the initial set-up, except when specified in the instructions.
1.
1.
Remove the upper rear panel and place the tank heater switch in
the “OFF” position and replace the panel.
2.
Connect the dispenser to the power source and turn-on the water
supply.
3.
Water will automatically flow into the tank to the proper level and
shut-off. This will take approximately 10 minutes.
4.
Disconnect the dispenser from the power source, remove the upper
rear panel and place the tank heater switch in the “ON” position,
and replace the panel.
5.
Connect the dispenser to the power source and wait approximately
twenty minutes for the water in the tank to heat.
6.
On models with ready indicator, the indicator will glow when the
proper water temperature for use is achieved.
NOTE - Discontinue dispensing if the indicator LED turns off. Dispense
only when the indicator LED glows.
ON
CAUTION
!
Failu
re To
Com
ply V
oids W
arran
ty!
Hot W
ater S
ystem
s – W
ater Ta
nk W
ill Fill
Autom
atically
When
Unit Is
Conn
ected T
o Pow
er!
Coffe
e Bre
wers –
Fill Th
e Wate
r Tank
In
Accord
ance W
ith The
Insta
llatio
n Instru
ctions
!
DO N
OT Tur
n On T
he Tan
k Heate
r Switc
h
Until
Water
Come
s From
Open
ed Fau
cet!
HAZA
RDO
US
VOLT
AGE
DISCO
NNEC
T FRO
M
POW
ER SO
URCE
BEFO
RE RE
MOVIN
G!
WAR
NING
O
N
ON
STO
P
REA
D N
OTIC
E
This equipm
ent is
to be instal
led to
com
ply
with the
Basic
Plum
bing
Code
of
the
Buildin
g Officials and
Code
Adm
inistrators Inte
rnatio
nal, Inc. (BO
CA)
and the
Food Service
Sanita
tion Manual
of the Food
and
Drug
Adm
inistrat
ion (FD
A).
P1770
P1771
Plumbing Hook-Up
1. Flush the water line and securely attach it to the flare fitting on the
rear of the dispenser.
2. Turn-on the water supply.
10420 101507
DRAINING THE DISPENSER
CAUTION - The dispenser must be disconnected from the power source throughout these steps.
1. Disconnect the dispenser from the power source.
1. Disconnect the dispenser from the power source.
2. Shut-off and disconnect the incoming water supply
3. Remove the 4-40 screws at the sides of the top panel.
4. Gently remove one of the grommets from the tank lid.
5. Insert a tube to the bottom of the tank and syphon ALL of the water out. Bunn-O-Matic has a syphon assembly
available (#12440.0000) for this purpose.
NOTE - The dispenser must be full using the INITIAL SET-UP steps before reconnecting to the power source.
CLEANING
The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all
surfaces on Bunn-O-Matic equipment.
WALL MOUNTED INSTALLATION
If the dispenser is wall mounted, the bottom of the dispenser should be at the same height as a counter or
table top. Use B.O.M. part #12542.0000 for side mounted Wall Bracket Kit or # 13125.0001 for front mounted
Wall Bracket Kit .
SUPPORT FOR LARGE RECEPTACLES
CAUTION: If the dispenser is to be used with larger receptacles such as pitchers or pots, those receptacles must
be adequately supported during dispensing of hot water to avoid spillage of very hot water. This support may be
provided by a table or counter top, or use B.O.M. part #12599.0000 Shelf Kit