Epson 7850p Ficha De Dados Do Produto
EPSON PowerLite 7850p Projector
6/03
EPSON PowerLite 7850p Projector
-
5
Starting Up the Projector
If you turn on your computer or video equipment before the
projector, the projector automatically selects the connected
source. If you turn on the projector first or you have multiple
sources connected, you may have to switch to the desired
source manually (see “Selecting the Image Source” on page 5).
projector, the projector automatically selects the connected
source. If you turn on the projector first or you have multiple
sources connected, you may have to switch to the desired
source manually (see “Selecting the Image Source” on page 5).
Turning On the Projector
1. Remove the lens cap.
2. Plug in the projector.
3. Wait a few seconds until the projector’s P power light stops
flashing and turns orange.
4. Press the red P
Power
button on top of the projector or on
the remote control.
Note: If you’re using the remote
control, make sure batteries are
installed and the power switch on
the side of the remote control is
turned on.
control, make sure batteries are
installed and the power switch on
the side of the remote control is
turned on.
The projector’s P power light flashes green as it warms up,
and an image begins to appear after about 30 seconds.
When the P power light stops flashing and remains green,
the projector is ready for use.
and an image begins to appear after about 30 seconds.
When the P power light stops flashing and remains green,
the projector is ready for use.
Warning: Never look into the lens when the lamp is on. This
can damage your eyes.
can damage your eyes.
5. If you’ve connected a Windows-based computer to the
projector, you may see a New Hardware Wizard saying
your computer has found a plug-and-play monitor; if so,
click
your computer has found a plug-and-play monitor; if so,
click
Cancel
.
Selecting the Image Source
If multiple devices are connected to the projector, you can use
the
the
Source
buttons on the projector or the remote control to
switch from one source to another:
❏ The projector’s control panel has two
Source
buttons.
Use the
Computer/DVI
button to
switch between EasyMP,
™
and
between equipment connected to the
Computer
and
DVI
ports.
Use the
Video/BNC
button to switch
between equipment connected to the
Video
,
S-Video
, and
BNC
ports.
❏ The remote control has six
Source
buttons. Use them to switch
between equipment connected to
the port identified on each button,
or select
between equipment connected to
the port identified on each button,
or select
EasyMP
to project
wirelessly or from a memory card.
You can preview all sources to help
you select the desired source, as described below.
you select the desired source, as described below.
The
Computer
and
BNC
ports can be set up to use different
input signals, so if you have equipment connected to one of
these ports, be sure to select the correct signal to match the
equipment you’re using. You can change the input signal
settings using the projector’s menu system as described in
“Types of Connections” on page 4.
these ports, be sure to select the correct signal to match the
equipment you’re using. You can change the input signal
settings using the projector’s menu system as described in
“Types of Connections” on page 4.
Previewing Image Sources
Use the preview function to select the image source when you
have connected multiple sources to the projector.
have connected multiple sources to the projector.
1. Press the
Preview
button on the
remote control.
You see the currently selected
source displayed on the screen, as
shown below. Other sources
(including the currently selected source) appear in smaller
preview windows on the right and bottom of the screen.
source displayed on the screen, as
shown below. Other sources
(including the currently selected source) appear in smaller
preview windows on the right and bottom of the screen.
.
If no equipment is connected to a port, or if there is no
incoming signal, the preview window for that source
appears blank.
incoming signal, the preview window for that source
appears blank.
Note: Movies are displayed as still images on the preview
screen.
screen.
Power button
Preview
Computer (Analog-RGB)
BNC
Video
S-Video
DVI
Computer
Currently selected source
Preview windows