Sony HT-7000DH Manual
69
US
F:\Sony SEM HA\Revision3-
7000DH\JC06xxx_2662265122HT7000DH_US\2662265122\US07REM_HT-7000DH-U.fm
7000DH\JC06xxx_2662265122HT7000DH_US\2662265122\US07REM_HT-7000DH-U.fm
masterpage: Right
HT-8000MH
2-662-265-12 (2)
Using the
Remote
Programming the remote
You can program the remote to control non-
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable
to control. Note that the remote can only
control components that accept infrared
wireless control signals.
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable
to control. Note that the remote can only
control components that accept infrared
wireless control signals.
1
Press AV ?/1 while holding
down RM SET UP.
down RM SET UP.
The indicator lights up.
2
Press the input button
(including TV ?/1) for the
component you want to control.
(including TV ?/1) for the
component you want to control.
For example, if you are going to control a
CD player, press SA-CD/CD.
CD player, press SA-CD/CD.
3
Press the numeric buttons to
enter the numeric code (or one
of the codes if more than one
code exists) corresponding to
the component and the maker
of the component you want to
control.
enter the numeric code (or one
of the codes if more than one
code exists) corresponding to
the component and the maker
of the component you want to
control.
See the tables on page 70 for information
on the numeric code(s) corresponding to
the component and the maker of the
component (the first digit and the last two
digits of the numeric code correspond to
the category and the maker’s code
respectively).
on the numeric code(s) corresponding to
the component and the maker of the
component (the first digit and the last two
digits of the numeric code correspond to
the category and the maker’s code
respectively).
4
Press ENTER.
Once the numeric code has been verified,
the indicator slowly flashes twice and the
remote automatically exits the
programming mode.
the indicator slowly flashes twice and the
remote automatically exits the
programming mode.
5
Repeat steps 1 to 4 to control
other components.
other components.
To cancel programming
Press RM SET UP during any step. The
remote automatically exits the programming
mode.
remote automatically exits the programming
mode.
To activate the input after
programming
programming
Press the programmed button to activate the
input you want.
input you want.
If programming is
unsuccessful, check the
following:
unsuccessful, check the
following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 4 times in quick
succession while entering the numeric code,
an error has occurred. Start again from step
1.
an error has occurred. Start again from step
1.
Notes
• The indicator turns off while a valid button is
pressed.
• In step 2, if several input buttons are pressed, only
the last pressed button is valid.
• In step 2, if you press TV ?/1, only TV VOL +/– ,
TV CH +/–, TV/VIDEO and WIDE buttons are
reprogrammed.
reprogrammed.
• In step 3, if an input button is pressed, the new
input is selected and the programming procedure
returns to the beginning of step 3.
returns to the beginning of step 3.
• For the numeric codes, only the first three numbers
entered are valid.
To clear the memory of the
remote
remote
To clear all programmes, do the following to
reset the remote to factory settings.
reset the remote to factory settings.
Press ?/1, AV ?/1 and MASTER
VOL – at the same time.
VOL – at the same time.
The indicator flashes 3 times, then goes off.
Using the Remote
continued
US01COV_HT-7000DH-U.book Page 69 Monday, August 14, 2006 9:22 AM