Sony MEX-N5100BT Manual
35
GB
To a common ground (earth) point
First connect the black ground (earth) lead, then
connect the yellow and red power supply leads.
connect the yellow and red power supply leads.
To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
the accessory position
If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
For MEX-N5100BT:
To a car’s illumination signal
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
lead to a common ground (earth) point.
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
when it is connected to a rear speaker cord.
Note
Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to avoid
damage.
Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to avoid
damage.
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
avoid damage.
To capture your voice during handsfree calling, you
need to install the microphone
need to install the microphone
.
Cautions
It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from interfering
with your driving operations.
Be sure to keep it and other parts from interfering
with your driving operations.
If airbags or any other shock-absorbing
equipment is in your car, contact the store where
you purchased this unit, or the car dealer, before
installation.
you purchased this unit, or the car dealer, before
installation.
Note
Before attaching the double-sided tape
Before attaching the double-sided tape
, clean the
surface of the dashboard with a dry cloth.
When using the steering wheel remote
control
control
Installation of the connection cable RC-SR1 (not
supplied) is required before use.
supplied) is required before use.
1
To enable the steering wheel remote control, select
[SET STEERING]
[SET STEERING]
[STR EDIT] to make the
registration (page 19).
When the registration completes, the steering wheel
remote control becomes available.
When the registration completes, the steering wheel
remote control becomes available.
Making connections
Front speaker
Subwoofer
Installing the microphone (MEX-
N5100BT only)
N5100BT only)
Using the wired remote control
Clip (not supplied)