Canon vb-s800d Manual

Plenum Mounting Kit SR30-P-VB 

Installation Guide

This “Installation Guide” explains the installation method using 

the Plenum Mounting Kit SR30-P-VB. Be sure to read the “Safety 

Precautions” section for correct use. After reading this Installation 

Guide, keep it in a readily accessible location for future reference. 

This camera is for indoor use only.
In addition to this “Installation Guide”, please also read the 

“Installation Guide” included with the camera.

 

Caution

   Request a professional installer for all 

installation work. Never try to install the 

camera yourself. Doing so may result in 

unforeseen accidents such as dropping 

the camera or electric shock.

Camera specific functions will be listed using the icons below.

 : VB-S30D   

 : VB-S31D   

 : VB-S800D/VB-S805D 

This Installation Guide uses the following symbols to indicate 
important information the user should know in order to use the 
product safely. Explanations are provided for each symbol so that 
users will understand the level of importance for each. Be sure to 
observe these items.

 

Failure to follow the instructions 

accompanied by this symbol may result in 

death or serious injury.

 

Failure to follow the instructions 

accompanied by this symbol may result in 

injury.

Failure to follow the instructions 

accompanied by this symbol may result in 

property damage. 

 

Do not install in the following places:

 

•  Places in direct sunlight, near heat-generating objects, or 

subject to high temperatures 

•  Places near fire sources or flammable solvents (alcohol, 

thinner, fuel, etc.) 

•  Humid or dusty places 

•  Places subject to oily smoke or steam 

•  Places subject to sea air

•  Confined or enclosed places

Failure to do so may result in fire or electric shock.

Precautions for the LAN (power) cable:

 

•  Do not set any heavy objects on the LAN cable.

•  Do not pull, forcibly bend, scratch, or modify the LAN cable.

Failure to do so may result in fire or electric shock.

 

For installation or inspection of this camera, consult the 

dealer where you purchased the product.

 

•  This installation should be made by a qualified service 

person and should conform to all local codes. 

•  When installing, make sure the surface is capable 

of withstanding the total weight of the camera and 

accessories, and sufficiently reinforce if necessary.

•  Periodically check the parts and screws for rust and 

loosening, in order to prevent injuries and equipment 

damage due to falling items.

•  Do not install in unstable places, places subject to 

significant vibration or impact, or places subject to salt 

damage or corrosive gas.

•  Be sure to attach the safety wire when installing the 

camera.

•  Use only with compatible cameras.

•  If a ceiling plate thickness is not between 10.0 and 

50.0 mm, do not use it.

Failure to do so may result in the camera falling or other 
accidents.

•  Do not touch the edges of metal parts with bare hands.

•  Be careful not to get your fingers caught when installing.

Failure to do so may result in injuries.

•  

 

 Do not turn the camera rotator by hand.

•  

 

 Do not install on an unstable surface. Also, make 

sure the camera is installed less than ±5° off horizontal.

•  After turning off the power, do not turn the power on again 

for at least five seconds.

•  Take measures to remove static electricity before 

performing any procedures.

•  If there is condensation, please wait to power on until the 

condensation dissipates.

Failure to do so may result in malfunctions.

•  Take care not to damage wiring or pipes.

Failure to do so may result in damage to peripheral items.

 

•  If you discover defective conditions such as smoke, 

strange sounds, heat or strange odors, immediately stop 

using the camera and contact your nearest dealer.

Fire or electric shock may result from continued use of the product.

•  If thunder starts, stop installation or inspection etc. and 

do not touch the camera or continue connecting the 

cable.

•  Do not disassemble or modify the camera.

•  Do not damage the connecting cable.

•  Do not spray the camera with water, or otherwise make it 

wet.

•  Do not insert foreign objects such as water or metal into 

the camera.

•  Do not use flammable sprays near the camera.

•  Do not leave LAN cables connected when the camera is 

not in use for long periods.

•  Do not use flammable solvents such as alcohol, paint 

thinner or benzine when cleaning the camera.

Failure to do so may result in fire or electric shock.

Model 

SR30-P-VB 

Weight 

Approx. 900 g (1.99 lb.) (Plenum Mounting Unit, Recessed 

Mounting Cover)

TORX is the trademark of Acument Intellectual Properties, 

LLC.

The contents of this guide are subject to change without any 

prior notice.

  158 (6.22)

166 (6.54)

76 (2.99)

12 (0.47)

  136 (5.35)

170 (6.09)

Unit : mm (in.)

Perform camera settings by using the software on the 
Setup CD-ROM (please refer to the “Operation Guide”).
Remove the tape affixed on the unit from the factory.
Attach the camera to the camera holder.

❶

❷

❸

        

   

a

a.

 Camera holder

        

M4 x 3

Screws 

(included)

BIE-7095-000

© CANON INC. 2016 

Printed in Taiwan

Plenum Mounting Unit  

Recessed Mounting Cover 

 

 

Sticker

 

Screws (M4) x 3

 

Template

 

Installation Guide (This document)