Netgear JWNR2000v2 - Wireless-N 300 Router Guia Da Instalação

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste 
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, 
this product should be treated and recycled in accordance with the laws of your jurisdiction 
implementing the WEEE Directive.

© 2011 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered 

trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names 

are trademarks or registered trademarks of their respective holders. Information is subject to change without 

notice. 

1.  In your browser address field type http://

www.routerlogin.net and click Enter. 

2.  When the Welcome screen opens, click 

Next. It will detect your type of internet 
connection. Follow the prompts to 
complete your router Internet connection.

1.  First, assign a name to your wireless 

network. Choose a name (SSID) that is easy 
to remember. You might want to write it 
down in the area provided on the middle 
panel. (Default is NETGEAR). Click Next. 

2.  Select the Yes option to add security then 

select your security method. NETGEAR 
recommends WPA-PSK [TKIP] + WPA2-PSK 
[AES ]. 

3.  Choose a Passphrase. You might want to 

write it down in the area provided on the 
middle panel. (Example: HomeNetwork). 
Click Next. 

Note: Both your network name (SSID) and 
passphrase are case sensitive.

4.  Review your network settings on the 

Success page. You may want to print this 
for your records. Click Next to apply all 
settings and continue to follow instructions 
in the next section.

1.  Open the software that manages your wireless connections on the wireless 

device that you want to connect to your router. (For example, on Windows XP, go 
to Control Panel ->Network Connections, right click the wireless device 
and select View Available Wireless Networks).

2.  The wireless software will scan for all wireless networks in your area. Look for 

and select the network name that you chose when you set up your router.

3.  If your network is secured, you will be prompted for a Passphrase or network key. 

Enter the Passphrase you selected and click Connect. You are now finished with 
the installation.
Note: If your wireless device supports WPS (WiFi Protected Setup)—NETGEAR 
calls this method Push 'N' Connect—you might be prompted to press a WPS 
button on the router instead of entering a Passphrase. If so, go to Step 4.

4.  Press the WPS button on the router. It will look similar to 

 or 

.

5.  Within 2 minutes, follow the wireless software instructions on the wireless device 

to complete the WPS process. The device will then be connected to your router. 
Repeat this process to add other wireless devices.
Note: Your network name, security method and passphrase must be the same on 
all wireless devices connected to your router.

Enter your wireless information here:
Wireless Network Name (SSID) ________________________________
Wireless Security Passphrase __________________________________
If you forget your Passphrase, connect a computer to the router using an 

Ethernet cable and log in to 

 and enter the 

default User Name (admin) and Password  (password). 

Restore Factory Default: For some routers, you may need to reset the 

device to its factory default first, then reconfigure your Passphrase. To restore 
factory defaults, use a paper clip to press the recessed reset button on the back 
until the Power/Test light blinks. This takes about 10 seconds. Release the 
button and wait for the router to reboot. Log in with the default username is 
(admin) and password (password). Note: Restoring factory defaults will erase 
any customizations and you will lose any configurations saved to the device!

Thank you for selecting NETGEAR products. 
After completing the setup and configuration, register your product at 

. Registration is required before you can use our 

telephone support service. 
Warning: Do not install this device on top of any other electrical equipment or 
install any other equipment on top of this device. Keep this device away from any 
heat sources such as direct sunlight, heaters, radiators, or other A/V receivers or 
devices that emit heat.
For complete DoC, please visit the NETGEAR EU Declarations of Conformity website 

For GNU General Public License (GPL) related information, please visit