Cisco Cisco IOS Software Releases 12.2 MC
![Cisco](https://files.manualsbrain.com/attachments/7380d0050044647c30f5c24bbbf5d0c0b6d9bb84/common/fit/150/50/faa183d287233c52228cfea3dbc2a127fe780f60564fcb0955d9c3d1cd23/brand_logo.png)
8
Release Notes for Cisco MWR 1941-DC Mobile Wireless Edge Router for Cisco IOS Release 12.2(15)MC1
OL-13984-06
Limitations, Restrictions, and Important Notes
Limitations, Restrictions, and Important Notes
Caution
The Cisco MWR 1941-DC router does not support online insertion and removal (OIR) of WAN interface
cards. Any attempt to perform OIR on a card in a powered up router might cause damage to the card.
cards. Any attempt to perform OIR on a card in a powered up router might cause damage to the card.
Caution
Removing the compact flash from the Cisco MWR 1941-DC router during a read/write operation might
corrupt the contents of the compact flash, rendering it useless. To recover from an accidental removal of
or corruption to the compact flash, a maintenance spare with the appropriate bootable Cisco IOS
software image might be needed.
corrupt the contents of the compact flash, rendering it useless. To recover from an accidental removal of
or corruption to the compact flash, a maintenance spare with the appropriate bootable Cisco IOS
software image might be needed.
Unsupported Cisco IOS Software Features
The Cisco MWR 1941-DC router requires a special version of Cisco IOS software. Not all Cisco IOS
software features can be used with the Cisco MWR 1941-DC router as the core routing is handled by the
network processor. The following standard Cisco IOS software features are not supported on the Cisco
MWR 1900 router:
software features can be used with the Cisco MWR 1941-DC router as the core routing is handled by the
network processor. The following standard Cisco IOS software features are not supported on the Cisco
MWR 1900 router:
•
Security Access Control Lists
•
MPLS
•
802.1Q VLANs
•
Frame Relay (FR)
•
MLP LFI
•
ATM
Upgrading the VWIC-2MFT-T1-DIR Microcode
When upgrading the image on your Cisco MWR 1941-DC router, power cycle the router or perform a
microcode reload on the VWIC-2MFT-T1-DIR to ensure that the firmware for the VWIC-2MFT-T1-DIR
is updated during the upgrade.
microcode reload on the VWIC-2MFT-T1-DIR to ensure that the firmware for the VWIC-2MFT-T1-DIR
is updated during the upgrade.
Disabling PPP Multiplexing
To fully disable PPP multiplexing (PPPMux), issue the no ppp mux command on the T1 interfaces of
the routers at both ends of the T1 link. If PPP multiplexing remains configured on one side of the link,
that side will offer to receive PPP multiplexed packets.
the routers at both ends of the T1 link. If PPP multiplexing remains configured on one side of the link,
that side will offer to receive PPP multiplexed packets.
MLP LFI Support
MLP LFI is not supported by the Cisco MWR 1941-DC router. Therefore, MLP LFI must be disabled on
peer devices connecting to the Cisco MWR 1941-DC router T1 MLP connections.
peer devices connecting to the Cisco MWR 1941-DC router T1 MLP connections.
ACFC and PFC Support on PPP Interfaces
If upgrading to Cisco IOS Release 12.2(8)MC2c or later for the ACFC and PFC support on PPP
interfaces, ensure that you upgrade the MGX-RPM-1FE-CP backcard image first. After doing so,
immediately upgrade all MWR 1941-DC routers connected to the MGX-RPM-1FE-CP back card.
interfaces, ensure that you upgrade the MGX-RPM-1FE-CP backcard image first. After doing so,
immediately upgrade all MWR 1941-DC routers connected to the MGX-RPM-1FE-CP back card.