Cisco Cisco TelePresence MX700 Manual De Manutenção

D14850.03 MX Series Administrator Guide (TC5.1) | 2012 FEBRUARY | © 2011-2012 Cisco Systems, Inc. All rights reserved. 

www.cisco.com

44

Network [1..1] QoS Diffserv Video

The Diffserv Video defines which priority Video packets should have in an IP network. Enter 

a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the 

priority. These priorities might be overridden when packets are leaving the network controlled by 

the local network administrator. NOTE: Requires the Network QoS Mode to be set to Diffserv.
Requires user role: ADMIN
Value space: <0..63>

Video: A recommended value is Diffserv Code Point (DSCP) AF41, which equals the value 

34. If in doubt, contact your network administrator.
Range: Select a value from 0 to 63.

Example: Network 1 QoS Diffserv Video: 0

Network [1..1] IEEE8021X Mode

The system can be connected to an IEEE 802.1X LAN network, with a port-based network 

access control that is used to provide authenticated network access for Ethernet networks.
Requires user role: ADMIN
Value space: <On/Off>

On: The 802.1X authentication is enabled.
Off: The 802.1X authentication is disabled (default). 

Example: Network 1 IEEE8021X Mode: Off

Network [1..1] IEEE8021X TlsVerify

Verification of the server-side certificate of an IEEE802.1x connection against the certificates in 

the local CA-list when TLS is used. The CA-list must be uploaded to the video system / codec.
This setting takes effect only when Network [1..1] IEEE8021X Eap Tls is enabled (On).
Requires user role: ADMIN
Value space: <Off/On>

Off: When set to Off, TLS connections are allowed without verifying the server-side X.509 

certificate against the local CA-list. This should typically be selected if no CA-list has been 

uploaded to the codec.
On: When set to On, the server-side X.509 certificate will be validated against the local CA-

list for all TLS connections. Only servers with a valid certificate will be allowed.

Example: xConfiguration Network 1 IEEE8021X TlsVerify: Off

Network [1..1] IEEE8021X UseClientCertificate

Authentication using a private key/certificate pair during an IEEE802.1x connection. The 

authentication X.509 certificate must be uploaded to the video system / codec.
Requires user role: ADMIN
Value space: <Off/On>

Off: When set to Off client-side authentication is not used (only server-side).
On: When set to On the client (codec) will perform a mutual authentication TLS handshake 

with the server.

Example: Network 1 IEEE8021X UseClientCertificate: Off

Network [1..1] IEEE8021X Identity

The 802.1X Identity is the user name needed for 802.1X authentication.
Requires user role: ADMIN
Value space: <S: 0, 64>

Format: String with a maximum of 64 characters. 

Example: Network 1 IEEE8021X Identity: ""

Network [1..1] IEEE8021X Password

The 802.1X Password is the password needed for 802.1X authentication.
Requires user role: ADMIN
Value space: <S: 0, 32>

Format: String with a maximum of 32 characters. 

Example: Network 1 IEEE8021X Password: "***"

Network [1..1] IEEE8021X AnonymousIdentity

The 802.1X Anonymous ID string is to be used as unencrypted identity with EAP (Extensible 

Authentication Protocol) types that support different tunneled identity, like EAP-PEAP and EAP-

TTLS. If set, the anonymous ID will be used for the initial (unencrypted) EAP Identity Request.
Requires user role: ADMIN
Value space: <S: 0, 64>

Format: String with a maximum of 64 characters. 

Example: Network 1 IEEE8021X AnonymousIdentity: ""

Introduction

Table of contents

Web interface

Advanced settings

Appendices

Advanced settings